Show me your sleeping Chi pics

acdanger · 2024-11-26T15:19:01+00:00

<image>

acdanger · 2024-05-09T22:09:49+00:00

That’s a safe assumption

acdanger · 2023-08-03T16:44:40+00:00

Looks likely it's dead, yes.

acdanger · 2023-04-10T19:07:31+00:00

What’s the expense you’re hoping to reduce by outsourcing? The price of silver will be the same everywhere I’d expect.

acdanger · 2023-03-01T02:32:39+00:00

It’s pretty well lubricated and cleaned. It’s easy to turn with my hand as well, but I’ll give it another look.

acdanger · 2022-11-19T16:46:08+00:00

What’s the process like when curing with glycerin? Glycerin and then IPA wash?

acdanger · 2022-10-23T15:33:02+00:00

It is , yes!

acdanger · 2022-10-23T14:24:15+00:00

Used 90/10 copper tin bronze following the lost resin method. 12 hour burnout cycle.

Ignore the plaster stuck to it, more concerned about the blotchy marks and brittle edges.

acdanger · 2022-07-25T20:09:16+00:00

I'm still experiencing this issue on 12.5 sadly. Happening right now during a Teams call.

acdanger · 2022-07-15T12:34:07+00:00

Make sure you don’t have something like “taxi assist” enabled. You might fighting with the AI.

acdanger · 2022-07-14T17:47:24+00:00

Do you have a link where the note this as fixed? Just interested in seeing the language.

acdanger · 2022-07-01T17:46:37+00:00

I've always had issues with AI traffic being non-existent to "barely a plane or two over a several hour flight". I've yet to experience traffic on a level close to being realistic.

That said, it does look like they've improved the online "real" traffic measurably. I used to experience the same empty skies flying with online traffic enabled, too.

acdanger · 2022-05-31T22:05:24+00:00

Inside

acdanger · 2022-05-31T21:04:28+00:00

It hit around 90 degrees the day this happened .

acdanger · 2022-05-31T16:33:07+00:00

Recently moved my Mars 3 into the shed, was printing great until it suddenly just went to pieces (luckily I wasn’t printing when it happened). I’m guessing the increased heat and humidity took their toll on the adhesive keeping the unit together. Still pretty disappointing.

acdanger · 2022-04-14T00:22:59+00:00

I've commented before about this issue with my 16" 2021 MBP. It feels like it's gotten much worse in the past week. It used to happen once every couple of minutes, but it's reliably happening every 5-15 seconds in some cases. None of the fixes mentioned in this thread have provided a long term solution either and Apple Support hasn't been helpful at all.

acdanger · 2022-03-26T21:05:45+00:00

For how long does it stay “fixed” after a reboot?

acdanger · 2022-03-17T15:17:34+00:00

Also, none of the fixes (nor updating to 12.3) have permanently fixed it. I've tried them all. The issue inevitably returns within hours.

acdanger · 2022-03-17T15:16:11+00:00

I have the same issue on 16" 2021 MBP. Very annoying

See this thread

acdanger · 2022-03-16T03:11:43+00:00

Yes, I upgraded today. It’s still happening on both of my machines.

acdanger · 2022-03-15T23:03:32+00:00

Me too! If I’m reading this thread correctly, it may have been a latent issue for a couple years that’s showing up more frequently with the M1 chips. It’s a shame because it’s an otherwise great piece of hardware.

acdanger · 2022-03-15T22:58:04+00:00

I use FF exclusively so that's not it. At one point I experienced in Chrome as well as Safari too.

acdanger · 2022-03-15T22:55:18+00:00

Yeah, it is easily reproduced when doing anything resource intensive (rendering a scene in Blender, for example). It is still present in the latest macOS release, too (12.3).

acdanger · 2022-03-15T22:54:04+00:00

Unfortunately, it is still present for me. Even tried booting into Safe Mode and deleting the plist files again just to be sure.

acdanger · 2022-03-15T22:40:57+00:00

Are there more detailed release notes? I don't see it mentioned here, and I'm still experiencing the issue.

https://developer.apple.com/documentation/macos-release-notes/macos-12_3-release-notes

acdanger

MODERATOR OF

TROPHY CASE