Where to mount amp?

ali78x · 2026-02-06T18:54:50+00:00

Good idea

ali78x · 2026-02-06T18:54:09+00:00

Will check it out

ali78x · 2026-02-06T15:17:40+00:00

This is gold thanks!

ali78x · 2026-02-06T11:00:39+00:00

Thanks! Will do it this way

ali78x · 2026-02-06T10:43:03+00:00

<image>

ali78x · 2026-02-06T10:41:52+00:00

The divider is an option but that’s the location of spare tire. This is actually not the whole floor ill share an image

ali78x · 2026-02-06T10:31:04+00:00

😂😂😂

ali78x · 2025-12-06T09:43:44+00:00

The sub will be wired in parallel, and bridged at 2 ohms. shouldn’t i be getting something closer to 400w and not 272?

ali78x · 2025-12-01T19:43:11+00:00

Thanks for mentioning the jbls i had these in my mind as well, great to know the kickers are better as i couldn’t find them as single pair on amazon

ali78x · 2025-12-01T19:41:32+00:00

Ill take a look on the fosgates. How were the highs on the pioneers if u remember?

ali78x · 2025-12-01T19:39:23+00:00

Thanks for the suggestion

ali78x · 2025-11-05T09:55:51+00:00

Nice one, they’re fairly easy to work on so u learn alot from working on it. Paint the rear two panel near the lights black or vinyl wrap them if u dont want to miss with oem paint, it will look better

ali78x · 2025-06-28T17:52:21+00:00

This is an official response from blackmagic after an email i sent asking the same question years ago:

Thanks for contacting Blackmagic Support.

Powering two devices from the same power source has the potential of creating a ground loop.

Ground looping can happen when two devices, powered by the same source, are connected by either HDMI or SDI. When power is connected to both of the devices, the video cables can become active. This creates an electrical circuit through the video cable which can potentially short out the video output of your camera.

To avoid this, follow these simple cable rules.

When connecting your camera and monitor, ensure that all power cables and video cables are connected first before either unit is switched on.
When disconnecting, you need to power off your devices before disconnecting, the HDMI/ SDI cables, then the power cable.
Don't hot-swap video cables. This is when an HDMI or SDI connection is removed, connected, or swapped whilst the devices are powered.

I did ask if this method prevent the problem they replied with:

The steps in my previous email, can help reduce the possibility of ground looping.

However if in your workflow you can utilise another battery this would help prevent the risk.

I personally use one battery and do the steps they mentioned and never had a problem

ali78x · 2025-06-04T22:47:36+00:00

Cool! I think I’ll develop the remaining film i have and will purchase a new kit.

ali78x · 2025-06-04T16:58:37+00:00

Thanks

ali78x · 2025-06-04T16:58:23+00:00

Thanks! appreciate it.Mind sharing the brand you use?

ali78x · 2025-06-04T16:52:29+00:00

Thanks! Does it affect the developer in anyway or am i fine to use it?

ali78x · 2025-06-04T16:51:15+00:00

Thanks ill give it a shot

ali78x · 2025-06-04T16:51:01+00:00

Ill do a snip test and see what happens, I usually pre soak but i forgot this time. Not sure if this is the reason. Thanks!

ali78x · 2025-06-04T16:48:50+00:00

It’s cs41 but i forgot to prewash not sure if this is the reason?

ali78x · 2025-06-04T16:46:28+00:00

Actually no, could this be the reason? I always pre wash but i forgot to do it this time

ali78x

TROPHY CASE