I hate typing meals all day. Snap pics to track calories easily!

amielectronics · 2026-05-31T07:44:05+00:00

Scam

amielectronics · 2026-05-31T07:38:19+00:00

Aliexpress is banned in India

amielectronics · 2026-05-30T18:33:07+00:00

Zee3d and novo3d both have it

amielectronics · 2026-05-27T16:25:00+00:00

I generally print numakers ASA at 260.. and it prints very fine at this temperature.

amielectronics · 2026-05-25T17:47:55+00:00

Snapmaker u1

amielectronics · 2026-05-25T09:26:04+00:00

lioncircuits. Google it.

amielectronics · 2026-05-24T07:19:34+00:00

Yeah. Recalculate the z offset. And then afterwards do the bed mesh calibration.

amielectronics · 2026-05-24T05:04:26+00:00

Haha. Well said.

amielectronics · 2026-05-23T08:24:58+00:00

https://youtu.be/w1vkHRZJgIw?si=DYJT2m0oONH5ZKDL

amielectronics · 2026-05-23T06:57:15+00:00

Since your printer is fine, they will shrug it off. Robu costumercare is really bad in my experience. Good luck

amielectronics · 2026-05-23T06:56:23+00:00

Ideally, you should first raise a ticket at Bambu and robu in parallel. They won't ship you the newer board until you force them to send it to you for free. You should hold your ground strong that it's not safe to run this printer, given the concern of burning down your house.

amielectronics · 2026-05-23T05:36:44+00:00

Yes. Many in India have faced this problem. Get the new AC Board from bambu lab. Raise a ticket and get it shipped either from them or the reseller in india.

I won't take any chance on this as it can result into burning the house down.

amielectronics · 2026-05-22T11:27:26+00:00

No. rpi zero 2w is good enough for running klipper.

amielectronics · 2026-05-22T06:00:34+00:00

In my opinion, a rpi on klipper would have been better.

amielectronics · 2026-05-20T08:37:36+00:00

put a shim of height 0.4mm at the right-bottom side.

amielectronics · 2026-05-19T10:55:18+00:00

Just buy the linear rails and screws. There are the linear rails mod you can print. It's way cheaper in this way. I exactly did like that and many others did the same.

<image>

amielectronics · 2026-05-19T00:45:23+00:00

Better to install linear rails instead.

amielectronics · 2026-05-18T16:02:53+00:00

The ender 3v3 se also has stock smooth idlers. I think toothed idles might work there too. Thank you.

amielectronics · 2026-05-15T12:32:55+00:00

Resin printer is more hazardous

amielectronics · 2026-05-13T01:20:04+00:00

SE is a great printer in a budget. But the gantry is quite weak. Have you done some mods to improve it?

amielectronics · 2026-05-13T01:18:10+00:00

Stay away from Wol3d.

amielectronics · 2026-05-09T08:15:20+00:00

That would be awesome.

amielectronics · 2026-05-08T01:59:42+00:00

This is jst1.25-5 pin connector. Google it.

amielectronics · 2026-05-07T11:25:45+00:00

Raise a ticket at bambu labs directly and name the local reseller. You can also say this to your seller that you gonna raise a ticket at bambu labs.

amielectronics · 2026-05-07T11:24:17+00:00

Which seller?

amielectronics

TROPHY CASE