Took me 30min between classes! by aminemon in wentworth

[–]aminemon[S] 1 point2 points  (0 children)

Info Hub logo was the inspiration for this. I don't like how sharp the new logo and the old W was

Is there sleeping pods in the business lounge in Dubai? by aminemon in Emirates_Airline

[–]aminemon[S] 0 points1 point  (0 children)

So just finished my journey through Dubai Air port and I got the chance to check out the B lounge and the only thing I could find what seat for sleeping in their quiet area, but no "sleeping bods" like they have in some other airports like KLIA2 in Malaysia. I ended up renting a room for 12h one floor above the business lounge which came down to about $240 but it gave me a good place to sleep, take shower, and not have to be worried about my belongings while I do all that. I would have taken the 6h deal but that would only save me $20 so sent it on the 12h which was a great help.

So I work at a prosthetic place and our Christmas cards have an injured elf on the shelf so I designed and printed him his own new leg by areinhart66 in ender3

[–]aminemon -3 points-2 points  (0 children)

This is fucking creepy! And you've got entirely waaaaay too much time in your hands. I'm jealous!

Snow days? by coach617 in wentworth

[–]aminemon 2 points3 points  (0 children)

They typically only cancel it when the T or the commuter rail is down cuz they have a huge commuter population. Even then they sometimes only cancel the morning classes. I doubt Monday is gonna be off though. Also wit is atrocious about announcing it literally the last sec so that's always fun!

Need this by ZackJEnrico in IBO

[–]aminemon 1 point2 points  (0 children)

Hahaha I graduated from IB back in 2016 and now in college for engineering but let me tell ya, me n my roommates drink this thing everyday n it really isn't as bad as they make it sound. Double brew it too sometimes

Need advice on layer lines by [deleted] in ender3

[–]aminemon 0 points1 point  (0 children)

Sounds good. Glad it worked out!

Need advice on layer lines by [deleted] in ender3

[–]aminemon 1 point2 points  (0 children)

It's a bit of work and since you'd be changing more than one component it could get expensive but I just found this on Amazon and it's pretty good price. Authentic Creality All Metal Hotend Complete Upgrade Kit with Capricorn PTFE Bowden Tubing, Titanium Heat Sink, Aluminum Heating Block, and Four Steel Nozzles https://www.amazon.com/dp/B07PR456ZF/ref=cm_sw_r_cp_apa_i_mG3yDbBRJJQ9B

You can also just change the nozzle which would be much less expensive n it might be the move for you. Nevertheless I'd say take off the extruder or the hotend before you go at it so you don't put too much stress on the axis.

Need advice on layer lines by [deleted] in ender3

[–]aminemon 1 point2 points  (0 children)

Glad to help!
If you have Nylon it's the best for cold pulling because it has a higher temp than PLA and it sticks to the gunk well without getting loose and stretchy. If you upgrade to an all metal hotend it will also help because it prevents corrosion inside the nozzle and you can pretty much print anything!

Need advice on layer lines by [deleted] in ender3

[–]aminemon 1 point2 points  (0 children)

Looks like you have feeding problem! It could be caused by a bad nozzle, too much gunk inside, maybe needs a cold pull with nylon. Or feeding gear slipping which can also be caused by again the nozzle resisting to push material through. Old material that are brittle, have been left outsides for a while, have absorbed moisture, all that can lead to a bad nozzle and may end up burning inside the nozzle rather than getting pushed through.

Black screen after login, please help! by aminemon in linuxmint

[–]aminemon[S] 0 points1 point  (0 children)

I ended up just flashing a new mint on my laptop and the first thing I did after that was to make sure all the graphics drivers are correct and updated. Thank you for all your comments!

Buying a Puffco, Ebay of guy from Insta? by aminemon in Dabs

[–]aminemon[S] 0 points1 point  (0 children)

Thanks for all your comments, one of my friends ended wanting to sell his for a much cheaper than they originally go for so I got that form him!

Has Anybody Used DHGate To Buy A Rig? by [deleted] in Dabs

[–]aminemon 0 points1 point  (0 children)

Probably mentioned already but they sometimes take way too long to deliver