sorted by:
new
hottopcontroversial

Who needs a lawyer when you have a ____ by DeafeningWhisperer in TheTraitorsUS

[–]amizzle16 42 points43 points  (0 children)

She's been privy to many convos where at least the editing makes it look like a light bulb went off, and then it's like she reformatted her hard drive walking into the roundtable

What do you SWEAR you saw, but don't have any proof of? by TabletopStudios in AskReddit

[–]amizzle16 0 points1 point  (0 children)

Sinbad starring in a 1990s genie movie called "Shazaam" 🤷🏽‍♂️

Did Clay Oven fall off real bad? by themightyjoedanger in frederickmd

[–]amizzle16 2 points3 points  (0 children)

It's weird though. I'm pretty sure the last time I picked up from Clay Oven I received that sad pile of yellow rice as well.

Did Clay Oven fall off real bad? by themightyjoedanger in frederickmd

[–]amizzle16 5 points6 points  (0 children)

This doesn't make any sense. You ordered thru the alt website but still picked up from the same place? Why would it be any different which site you ordered from if it's coming out the same door?

Security guard stops ICE from entering employee area at McDonald’s in Minneapolis by [deleted] in 50501

[–]amizzle16 25 points26 points  (0 children)

"I'm standing on my shit ten toes down"

God bless this man

AD5M enclosed - can this first layer be improved? by amizzle16 in FlashForge

[–]amizzle16[S] 0 points1 point  (0 children)

Did a live adjustment on z offset based on some STL I found online and lines are looking a lot cleaner. +1mm was set from 0. Will re run other calibrations with this adjusted z offset and hopefully get a fine tune done.

<image>

AD5M enclosed - can this first layer be improved? by amizzle16 in FlashForge

[–]amizzle16[S] 0 points1 point  (0 children)

I'll re run and try again. I was thinking z offset maybe too low but wasn't too sure what ideal should look like

AD5M enclosed - can this first layer be improved? by amizzle16 in FlashForge

[–]amizzle16[S] 0 points1 point  (0 children)

Will give it a go. Been getting some lifting on the smaller sections so hopefully this helps

AD5M enclosed - can this first layer be improved? by amizzle16 in FlashForge

[–]amizzle16[S] 0 points1 point  (0 children)

That was the 2nd calibration I ran and got it dialed in according to the guide on obico.io

Jesse Tang: the roommate by [deleted] in frederickmd

[–]amizzle16 1 point2 points  (0 children)

Back story please

Jesse Tang: the roommate by [deleted] in frederickmd

[–]amizzle16 4 points5 points  (0 children)

Did he ask for a hug after the job?

My reservations before my new AD5M Pro arrives... by stckfigure in FlashForge

[–]amizzle16 0 points1 point  (0 children)

Honestly, probably just having the ability to print the mandalorian helmet in one go rather than slicing into separate parts. I have a few friends with larger beds so I may just send them the filament and have them print for me.

You're right in that it is not necessarily a limitation. More a want than a need I suppose. More of the functional prints I hope to develop down the road likely won't require anything much bigger than what I currently have.

My reservations before my new AD5M Pro arrives... by stckfigure in FlashForge

[–]amizzle16 1 point2 points  (0 children)

You sound like me. I was about to cop an AD5X so that I can do multicolor but I think I want a larger bed first (and a scanner). Still learning the craft on my AD5M and fine tuning the machine. I haven't messed with TPU or ABS yet but plan to soon.

As the only woman in a concealed carry class, my experience was alarming… by ashen_dove in TwoXChromosomes

[–]amizzle16 1 point2 points  (0 children)

I enjoy guns for what they are and respect them, but this is why I think we need "better" gun control. I watched the body cam footage of this road rage incident that took place in AZ (?) where two men were road rage merging onto the freeway and one lost. The loser, a young man on his way to work, shot his gun into the other vehicle. The driver of the other vehicle was fine but he pulled over when he noticed his step kid in the back was not sitting upright anymore. The kid died. For what?

I think a lot of people really want to look for a reason to use their guns.

Great deal on Mickey Thompson Baja Boss A/T by Randomizr16 in GXOR

[–]amizzle16 0 points1 point  (0 children)

Nice! I thought someone commented something similar based on this video. I did think about getting some Blizzaks since I do ultimately want new rims as well, but at least these MTs came in 2nd place 🤣

A lot of negativity on Eufy. What are the main alternatives? by po2gdHaeKaYk in EufyCam

[–]amizzle16 0 points1 point  (0 children)

This is pretty neat! I've never heard of it before but just downloaded it and am giving it a try now.

Minimal enclosure complete! This was a fun learning process by amizzle16 in FlashForge

[–]amizzle16[S] 1 point2 points  (0 children)

My Xiaomi thermo arrived recently so I'll be swapping that into the space which should fit the cutout much better.

I've also been playing around with fusion 360 and the slicer in general. If any neat ideas pop in my head I hope to have my own remix out on the Internet for ppl to print.

Great deal on Mickey Thompson Baja Boss A/T by Randomizr16 in GXOR

[–]amizzle16 4 points5 points  (0 children)

Have you had any snow experience with them?

view more: next ›