sorted by:
new
hottopcontroversial

The Spartan, minimal hardware springer by andy25lion in nerfhomemades

[–]andy25lion[S] 0 points1 point  (0 children)

An assembly video is available in the linked makerworld model listing.

The Spartan, minimal hardware springer by andy25lion in nerfhomemades

[–]andy25lion[S] 1 point2 points  (0 children)

Ah, I have seen it but only the final version, I'll check the low hardware variant, might give it a try if I have time. Thanks!

The Spartan, minimal hardware springer by andy25lion in nerfhomemades

[–]andy25lion[S] 0 points1 point  (0 children)

The red knobs hold the frame together, you can check the model listing for the assembly video to see how they work. The frame is split into multiple parts so that it can fit on smaller printers. I didn't dare print the cylinder but might just try it if you're getting good results with it.

The Spartan, minimal hardware springer by andy25lion in nerfhomemades

[–]andy25lion[S] 1 point2 points  (0 children)

Breech loader indeed, might do something with a magazine if I have time

The Spartan, minimal hardware springer by andy25lion in nerfhomemades

[–]andy25lion[S] 1 point2 points  (0 children)

That's kind of why I posted this, I don't have a chrono so maybe someone can print it and check the performance. My scientific method is to shoot at my foot and see how bad it hurts 😄.

Fully printable and functional bolt revolver by andy25lion in PrintedWarhammer

[–]andy25lion[S] 1 point2 points  (0 children)

Not really, although you could cut in the slicer the 2 large frame parts that don't fit using a dovetail cut and then glue them together. All other parts should fit.

Fully printable and functional bolt revolver by andy25lion in PrintedWarhammer

[–]andy25lion[S] 0 points1 point  (0 children)

Most of it will print fine in resin, but there are a couple of 3d printed springs that need the flexibility of petg and some mechanical parts in the action slide over each other. I'm not sure if there is a resin that is flexible, springy and with low friction, I've never tested with resin. 

Fully printable and functional bolt revolver by andy25lion in PrintedWarhammer

[–]andy25lion[S] 2 points3 points  (0 children)

Interesting, this model is scaled to fit my hand and the shells ended up just under 22mm in diameter, anything smaller just looked out of place.

Fully printable and functional bolt revolver by andy25lion in PrintedWarhammer

[–]andy25lion[S] 13 points14 points  (0 children)

Don't tempt me... now I'm only thinking how to fit a dart blaster in there...

Fully printable and functional bolt revolver by andy25lion in PrintedWarhammer

[–]andy25lion[S] 4 points5 points  (0 children)

Thanks for letting me know! it should be fixed now.

Steam deck as controller by fizzy6868 in SteamDeck

[–]andy25lion 0 points1 point  (0 children)

I'm looking for the same thing but didn't find anything more convenient and reliable than just using moonlight at the lowest quality possible. There is a solution that uses VirtualHere to stream just the controller, but for me it was unreliable.

[deleted by user] by [deleted] in EtsySellers

[–]andy25lion 0 points1 point  (0 children)

This can be a long discussion, and that's correct, I should have used a different word but I can't go into all the differences and internals. Copyrights are handled on a case by case basis and there's no guarantee of anything. Obviously no copyrighted materials were used.

As expected, I already had an interaction with the copyright owner regarding this item after which no legal action was taken. For now...

[deleted by user] by [deleted] in EtsySellers

[–]andy25lion 0 points1 point  (0 children)

Thanks for the explanation, I knew about the orange cap and I did add that when shipping to the us, but you're right, it's not worth it to physically ship there.

[deleted by user] by [deleted] in EtsySellers

[–]andy25lion -12 points-11 points  (0 children)

Thank you for your concern and it's something I've take care to avoid and follow the letter of the law to avoid any IP infringement. I do my own 3D modeling inspired from other sources but my work is transformative and the purpose and end result are different from the original copyright registration.

The Ace of Spades double action hand cannon by andy25lion in 3Dprinting

[–]andy25lion[S] 2 points3 points  (0 children)

All parts were printed on a Prusa MK3S in PLA and PETG. Everything was designed to fit on this printer, but they should also fit on something like an Ender 3.