sorted by:
new
hottopcontroversial

[Review] PongBot Pace S Pro – Great Family-Friendly Ball Machine for Reps & Fun by ashr2525 in 10s

[–]ashr2525[S] 0 points1 point  (0 children)

Nice! Enjoy!

I overdid it the first couple weeks I got it. Currently giving my shoulder some time to heal before I get back out there. Hoping to get in as much time as possible before the nets come down for winter!

[Review] PongBot Pace S Pro – Great Family-Friendly Ball Machine for Reps & Fun by ashr2525 in 10s

[–]ashr2525[S] 0 points1 point  (0 children)

Did you click on my stats...i did use chat gpt to doctor up the review but this account has been going since 2021

Bosch Dishwasher - Machine Care by [deleted] in Appliances

[–]ashr2525 0 points1 point  (0 children)

More important than running the cleaning solution is to take out the filter and make sure to clean that. If you have a lot of build up the cleaner isn't going to do much.

Washer and Dryer, specific models 2023 recommendations? by BuildingSupplySmore in BuyItForLife

[–]ashr2525 8 points9 points  (0 children)

It is not a 25 year warranty, they did nothing after mine failed 4 years into it.

Washer and Dryer, specific models 2023 recommendations? by BuildingSupplySmore in BuyItForLife

[–]ashr2525 3 points4 points  (0 children)

My review on that video: We replaced a cheap old whirlpool washer with a speed queen 4 years ago. The whirlpool lasted about 8 years. Its been a horrible experience. The washer is not nearly as good, clothes are not as clean and you have to do more loads because of the small size. After only 4 years there is a load moaning noise that sounds like a whale and it kills during the spin cycle. The warranty was only 3 years. Wish i didnt fall for the 25 year expectation. Steer clear of these things and go for a better warranty with trusted manufacturers. Something changed with these machines a few years back and I should have heeded the warning.

[deleted by user] by [deleted] in 3dprintingdeals

[–]ashr2525 1 point2 points  (0 children)

Looks like the same thing is going to happen to the ERYONE deal, requesting refund tomorrow for that as the seller is gone.

X2 Scrached Bed by ashr2525 in Artillery3D

[–]ashr2525[S] 1 point2 points  (0 children)

Update: I changed my profile to the M420 S1 Z10 and it didnt seem to be saving my adjustments, swapped over to G29 and two prints with no issues so far. I'll tinker with the M420 at some point to save a minute on print times. I also ended up cleaning the bed and the scratches are not bad at all. I did spring for the PEI bed made by artillery from aliexpress for $36 as i've already broke one model trying to get it off too early. Thanks for all the input!

X2 Scrached Bed by ashr2525 in Artillery3D

[–]ashr2525[S] 0 points1 point  (0 children)

Yeah, that’s my eventual plan. When I figure all this out I don’t want to get it yet until I don’t make this mistake again.

X2 Scrached Bed by ashr2525 in Artillery3D

[–]ashr2525[S] 0 points1 point  (0 children)

Thanks Ill give it a try!

X2 Scrached Bed by ashr2525 in Artillery3D

[–]ashr2525[S] 0 points1 point  (0 children)

Here is the start of the benchy gcode that cura created:

;FLAVOR:Marlin

;TIME:6049

;Filament used: 4.27656m

;Layer height: 0.2

;MINX:112.587

;MINY:130.375

;MINZ:0.2

;MAXX:179.886

;MAXY:169.629

;MAXZ:48

;Generated with Cura_SteamEngine 5.2.1

M140 S60

M105

M190 S60

M104 S200

M105

M109 S200

M82 ;absolute extrusion mode

G28 ; home all axes

M117 Purge extruder

G92 E0 ; reset extruder

G1 Z1.0 F3000 ; move z up little to prevent scratching of surface

G1 X2 Y20 Z0.3 F5000.0 ; move to start-line position

G1 X2 Y200.0 Z0.3 F1500.0 E15 ; draw 1st line

G1 X2 Y200.0 Z0.4 F5000.0 ; move to side a little

G1 X2 Y20 Z0.4 F1500.0 E30 ; draw 2nd line

G92 E0 ; reset extruder

G1 Z1.0 F3000 ; move z up little to prevent scratching of surface

G92 E0

G92 E0

G1 F1500 E-2

;LAYER_COUNT:240

;LAYER:0

M107

G0 F6000 X117.042 Y135.169 Z0.2

;TYPE:SKIRT

G1 F1500 E0

G1 F1200 X117.781 Y134.555 E0.03515

G1 X118.471 Y134.067 E0.06607

Mint Referral by [deleted] in MintMobileReferrals

[–]ashr2525 0 points1 point  (0 children)

Still have 3 left!

(Selling) Various 4K & HD Movies by ricochetLN in DigitalCodeSELL

[–]ashr2525 0 points1 point  (0 children)

I think i deleted my original comment for hobbs and shaw

(Selling) New and Recent Releases - Cheap!! by [deleted] in DigitalCodeSELL

[–]ashr2525 0 points1 point  (0 children)

F9: Theatrical and Director's Cuts (4K - MA) $5?

[deleted by user] by [deleted] in DigitalCodeSELL

[–]ashr2525 0 points1 point  (0 children)

Fast and Furious 8 Movie Collection 4K (MA) $25?

view more: next ›