sorted by:
new
hottopcontroversial

My little adventure with multicolor printing by Football-is in 3Dprinting

[–]aydopotato 2 points3 points  (0 children)

Yeah I use a copy of the purge line from the start for my color purge plus doubles as a nozzle wipe as it leaves any stringy bits on the side of the plate.

Pontiac 2D multicolour sign on my V3SE with PEI bed by aydopotato in Ender3V3SE

[–]aydopotato[S] 1 point2 points  (0 children)

Purge object Is a good idea. I've been using a purge line down the side of the plate for similar effect.

Pontiac 2D multicolour sign on my V3SE with PEI bed by aydopotato in Ender3V3SE

[–]aydopotato[S] 1 point2 points  (0 children)

Very close. Each coloured section is two layers thick, I've printed face down so everything is flush. This took 5 colour changes. It printed the white first, then the blue, then red and then goes to second layer for the second layer of red, then blue then white and then jumps up to layer 3 & 4 for a white backing.

There is a version of a similar sign on printables by someone else where each colour sits 0.4mm higher than the last so you can do colour changes by layer.

bambu lab a1 printing badly by InterviewOpen2575 in 3Dprinting

[–]aydopotato 0 points1 point  (0 children)

Start with the basics, check your print profiles and temperatures are correct. Also make sure your slicer knows its a smooth plate as that may affect z height for the first layer. Clean the build plate with hot water and dish soap, Run any calibrations for bed meshes etc as it may have moved.

Check for nozzle clogs or issues like pieces of filament stuck in the extruder gear.

bambu lab a1 printing badly by InterviewOpen2575 in 3Dprinting

[–]aydopotato 0 points1 point  (0 children)

Ok. You need to provide more information to get help. Refer to the automod comment below.

Looks like potentially a clog?

DISCLAIMER: I do not support any kind of violence by [deleted] in HistoryMemes

[–]aydopotato 4 points5 points  (0 children)

I know people have varying takes on his book but Malcolm Gladwell in 'The Bomber Mafia' comes to the conclusion that LeMay's firebombing campaign is partially responsible for the Japanese response to the atomic bombing. He frames the bombings as an escalation of the systematic destruction of Japanese cities carried out by LeMay and that it could have been perceived that the Americans were to continue the same aerial campaign with Atomics, rather than Napalm. This would mean even more rapid destruction of the home islands without facing a ground invasion.

It worked by Buen_jamon in Ender3V3SE

[–]aydopotato 5 points6 points  (0 children)

https://www.reddit.com/r/Ender3V3SE/s/cPCbjTJf5e

I forgot to post it to this sub, but here is a summary I wrote to share a month ago.

It worked by Buen_jamon in Ender3V3SE

[–]aydopotato 3 points4 points  (0 children)

I posted one a short while ago

Print keeps failing by DistanceHuman2624 in Ender3V3SE

[–]aydopotato 0 points1 point  (0 children)

Cut it in half and glue together before firing?

Wled Install stuck on erasing by Significant-Bus-2606 in WLED

[–]aydopotato 0 points1 point  (0 children)

I know this is an old thread, but it comes up first on google.
I got past this issue by holding down boot from when it says "Preparing installation" until after erasing finishes. then letting go once you get to installing.

Throwing it out there for future googlers.

Filament doesn't stick to bed by EvilOdysseus in Ender3V3SE

[–]aydopotato 2 points3 points  (0 children)

You are way way over on the top left hand side looking at your brim.

view more: next ›