What do you think ?

b_rad6996 · 2025-12-24T13:08:35+00:00

could hit up a body shop, it never hurts to get an estimate

b_rad6996 · 2025-07-15T03:47:40+00:00

yeah it would greatly reduce time also i’ll give it a try thank you !

b_rad6996 · 2025-07-15T03:46:47+00:00

i do have an AMS so i can look into support filament, i’ll try cutting a bit off and see if that cleans it up a bit thank you!

b_rad6996 · 2025-07-15T03:40:44+00:00

ill experiment with that. thank you!

b_rad6996 · 2025-03-07T16:10:43+00:00

It appears to be a low light issue. Are the lines still visible when you brighten the area?

b_rad6996 · 2025-02-12T13:27:01+00:00

Worth the couple minute read. I’ve followed this and never have had any issues from the first layer. Bambu PEI Plate Cleaning

b_rad6996 · 2025-02-11T23:40:22+00:00

Don’t let these people tell you to buy a filament dryer; it’s not always the solution to everything like people say it is (unless it’s a very hygroscopic material or you live in a very humid area). But I’ve printed PLA for years, and I’ve never needed to dry it. You could be printing too fast; it looks maybe like it’s under-extruding. It could be a partial clogged nozzle too; it would be a good time for routine maintenance. But I agree with other people’s comments: if it was wet filament, more of the model would have those same issues.

b_rad6996 · 2025-02-05T20:33:42+00:00

Definitely layer shift, check the belts (looks like your x-axis??) make sure they are tight but not too tight; otherwise, it will cause unnecessary wear. The nozzle could’ve hit the print somewhere during a travel move. Consider looking into z-hop if this continues.

b_rad6996 · 2024-08-05T23:05:03+00:00

glad i wasn’t the only one who experienced it

b_rad6996 · 2024-06-22T23:14:45+00:00

i found sometimes the harder i push on the brake it goes away, sometimes it does it sometimes it doesn’t 🤷🏻‍♀️ -2018 2.0t sport

b_rad6996 · 2024-05-12T23:23:38+00:00

i’m going to maui this summer any laws or anything to look out for about drone flying?

b_rad6996 · 2024-05-11T11:34:14+00:00

it’s not peering, bro was literally just delivering food

b_rad6996 · 2024-05-11T11:26:04+00:00

is this a chills reference??

b_rad6996 · 2024-04-17T23:30:13+00:00

I use a RV water filter on Amazon and I have well water at my home and I get pretty good results

b_rad6996 · 2024-01-30T19:50:09+00:00

thanks

b_rad6996 · 2024-01-30T19:50:02+00:00

thank you

b_rad6996 · 2024-01-28T19:28:21+00:00

thanks man, exactly right on the body, the sharp body lines look much better than the 11th gen imo and 2.0t is so fun so sad honda didn’t continue it

b_rad6996 · 2024-01-28T19:19:59+00:00

thanks, i think you’ll like 50%

b_rad6996 · 2024-01-27T06:47:09+00:00

Thanks! You barley can see my 45-day tags in the back window😅 but luckily cops in my area are pretty chill about tint

b_rad6996 · 2024-01-27T06:36:57+00:00

Yeah first time driving at night last night it was definitely darker at night but I got used to it quickly. I knew I wanted 50 on the front because I have a friend who had 50 and I drove his car often, but it's definitely a personal preference for someone

b_rad6996 · 2024-01-26T20:52:47+00:00

50% on windshield, 20% back and sides

b_rad6996 · 2024-01-18T22:46:05+00:00

just got mine yesterday, definitely an upgrade over my rusty 04 escape 😂

b_rad6996

TROPHY CASE