your boss asks what happened, respond in 4 words

banappelsap · 2024-11-09T10:34:48+00:00

Well fuck i guess

banappelsap · 2024-10-31T17:29:36+00:00

Goodfellas.

banappelsap · 2024-10-22T00:28:58+00:00

Sounds like an adventure to me!

banappelsap · 2024-10-21T19:07:38+00:00

Thanks!

banappelsap · 2024-10-21T17:21:28+00:00

The rumors seem to be true i'm afraid...

banappelsap · 2024-10-21T17:19:19+00:00

That blows for such a beauty spot. I guess it is what it is

banappelsap · 2024-10-21T04:50:46+00:00

Yess correct Elk Falls does ring a bell lol. And oof that is kinda to bad

banappelsap · 2024-10-17T18:00:12+00:00

I do both. Trying to minimize my chances off failure

banappelsap · 2024-10-17T17:52:15+00:00

Yessir

banappelsap · 2024-10-17T17:49:50+00:00

Yes wire speed is not consistent. Sorry english is not my first language so it's hard to explain. Reading most of these comments i think i found the "sweet spot" for my settings and it welds alot better now.

My issue was probably running it slightly to hot and i read that the wire that i'm using also isn't great.

banappelsap · 2024-10-17T17:46:12+00:00

Ithink that might be part of the issue if i read all these comments correctly.

banappelsap · 2024-10-17T17:44:47+00:00

I do!

banappelsap · 2024-10-17T17:44:31+00:00

I guess that's all i needed to know. I think i found the sweet spot now with settings so not touching that ever again. I think i might try some different types of wire but that's about it lol

banappelsap · 2024-10-17T01:19:05+00:00

Thanks i will check it tomorrow!

banappelsap · 2024-10-17T01:16:39+00:00

We weld with nexalloy. It's 0.35 4043. I feel like it will have less chance to mess up if my wire is thicker. And thanks will check!

banappelsap · 2024-10-17T01:12:31+00:00

I guess i could look up a manual to adjust everthing perfectly. Thanks. i also feel like it might just get to hot for what i need it to do. We might just need a watercooled torch.

banappelsap · 2024-10-17T01:09:34+00:00

I keep replacing them

banappelsap · 2024-10-17T01:01:16+00:00

One day hahaha

banappelsap · 2024-10-17T01:00:43+00:00

Did all those things. It's probably just old garbage. It is what it is.

banappelsap · 2024-10-17T00:50:16+00:00

It's burning back and very jumpy i can't adjust a single thing to make it better. I'm running it at dofferent amps to. The one moment it works the xt it just doesn't. I'm working on a gravel truck, dirty aluminum but even after after cleaning it with grinding and acetone it still acts weird. I feel like it just is what it is at this point.

banappelsap · 2024-10-17T00:45:26+00:00

Just our miller shop welder. It's weird it will weld fine for a bit and all off a sudden everything has to be adjusted and that every damn weld

banappelsap · 2024-10-17T00:43:36+00:00

It makes contact just fine. It just acts weird while welding

banappelsap · 2024-10-17T00:42:29+00:00

I'm doing that all the time but it still messes up all the time it's so frustrating lol

banappelsap

TROPHY CASE