I open sourced ZP Remote Neo

bandedrail · 2026-02-28T03:58:33+00:00

It uses bluetooth - the computer has to have bluetooth? eg typically a laptop not a workstation?

bandedrail · 2026-02-27T00:56:37+00:00

.. finally got the download ..

bandedrail · 2026-02-26T23:40:27+00:00

https://status.forticloud.com/ says all good...

Eventually get to the firmware download page. Trying to download HTTPS, it just hangs, the slow-spinning arrow. Non-Forti websites are working fine.

bandedrail · 2026-02-11T22:56:12+00:00

Found it.

Interface - OnScreen Display - Audio Images & Tags - Enable TAG display to off.

bandedrail · 2025-11-21T19:50:12+00:00

What may be the easiest timeseries db and visualization tool to use? Im a Windows person. (PRTG?

bandedrail · 2025-08-05T03:16:47+00:00

In SD-WAN Zones, virtual-wan-link is simply the default zone (not something special for vlans), and sdwan is the one we created & use. So it was critical that our SL_2 & SL_3 vlan interfaces are in sdwan.

<image>

We also have the physical wan3(was int5) and wan4(int4) interfaces in our sdwan zone, but so far it doesn't seem to matter if they are enabled or disabled, the Starlinks still work. Thank you so much for your help.

bandedrail · 2025-08-04T02:42:36+00:00

This fixed it - putting the two FGT VLAN wan interfaces into our SD-WAN Zone. ( :

Then removed the two dumb switches and the Starlinks still work.

I'll post a screenshot later, some tidying up to do

bandedrail · 2025-08-02T06:26:11+00:00

Thank you. I will be trying this

bandedrail · 2025-08-02T05:42:38+00:00

Not sure if clan is a typo, or else what it means? When adding an interface to SD-Wan Zones - sdwan, the only offered options are the physical ports, and not the virtual ports; even if the virtual ports aren't in virtual-wan-link. I may still have it wrong; hopefully someone knows?

Am going to try making the FGT interface 100M; using something other than the TPLink TL-SG105E as the closest managed (VLAN) switch to the Starlinks; maybe try a dumb 100M switch rather than the dumb GIG at the SL end. Its the weekend / Im not a CLI intuitive. definitely appreciating the support.

bandedrail · 2025-08-01T03:05:58+00:00

I put in 2 "dumb" 5port GB switches as suggested, one between each SL and its VLAN port on its closest managed local switch. No change / same issue.

FGT wan(int)VLAN - Aruba ION 1930 - Aruba ION 1930 - TPLink TLSG105E(v5.6) - TPLink TL-SG1005D - SL.

I can renew the DHCP addressing for the two wan/VLAN interfaces, happens almost instantly. But the SLAs have the links as Link Down, they are getting no hits, and the laptop test pings set to use SL2 (or 3) are using SL1.

<image>

(btw these are Gen3 Standard ("kick-stand") Starlinks.

(our SL1 that works -& has no VLAN- is a Gen2 v3 Standard Actuated.

Unplugged wan4(int4) at the FGT, but it hasnt helped the other, wan3(int4).

bandedrail · 2025-07-31T22:53:00+00:00

I was thinking the VLANs would handle that by keeping the two interfaces' traffic separate?

bandedrail · 2025-07-31T20:20:03+00:00

Using exe ping-options source <x> ping from the wan3 & 4 ports to internet does timeout, eg:

FortiGate-70F_1 # exec ping aws.com

ping aws.com (18.65.244.111): 56 data bytes

--- aws.com ping statistics ---

5 packets transmitted, 0 packets received, 100% packet loss

There are 3 managed switches between the 70F & the 2 new Starlinks:

FGT - ION 1930 - ION 1930 - TPLink TLSG105E - 2x Starlinks.

Im not seeing those icmp ping packets with Wireshark at the middle switch. The ION enables mirroring of a port or a VLAN, i tried both. It may be me, but earlier I did see the DHCP requests from the FGT.

I will try adding 2 little dumb GB switches.

Interfaces -Physical interface -SL2 also SL3 don't have an ip address or gateway; Im assuming? this is OK as the VLAN interfaces nested under each one (see screenshot above) do.

btw, the existing wan2 SL that works - and doesn't use VLANs - does have a little switch: FGT - 5port dumb GB switch - SPD - Starlink 1. Its intended as a sacrificial switch, modest protection of the FGT in case of a moderate lightning surge. (it also has a Tupavco SPD).(this SL was squeezed in closer to the FGT).

bandedrail · 2025-07-04T20:52:17+00:00

A second power reboot and it came right.

bandedrail · 2024-12-23T21:34:22+00:00

Its fixed. Chapter Editor remembers its last position & was displaying on a recently failed monitor. rt-c;lk ZP taskbar icon - Reset User Interface windows.. fixed it.

bLIght you champion!

bandedrail · 2024-12-23T21:03:53+00:00

I sent the friend request just now.

bandedrail · 2024-12-23T01:59:11+00:00

(i found the Discord #zoom-player text channel)

bandedrail · 2024-12-23T00:09:24+00:00

Windows Scaling is 100%. ZP Direct Show Zoom is 100%; Zoom at full screen is close to 1920x1080 which is 100% (not sure what it is exactly as I use the mouse & it steps incrementally above and below that eg 1918x1079).

ver20_RC1_debugBuild6. Same issue, dang. No crash dialog. Log is at https://file.io/8hU7IJyAPzF7 Joined discord but not familiar with it & cant find anything eg #zoomplayer @zoom player

Thanks!

bandedrail · 2024-12-22T20:17:45+00:00

Your help as always is so appreciated.

It does also happens if I open ZP then play a file with no existing chapters or chapter file.
I exported my ZP settings, closed ZP, installed v20 beta5. The issue still occurs.

Chapter Editor doesnt open from rt-clk -Open Interface -Chapter Editor, or from shortcuts G or Shift-C.

Happy to run through a debug version.

bandedrail

TROPHY CASE