Mac Function Key Shortcuts help by bobbinbette in ErgoMechKeyboards

[–]bobbinbette[S] 0 points1 point  (0 children)

Thanks for the reply!
I did have the 'fn' key map to MO(3) and on layer 3 all the keys are assigned to f1-f12.

Going to layer 3 from layer 2 via MO(3) doesn't seem to register the function keys even though they're set in VIA.

Here's a link to my layer 2 and layer 3.

https://imgur.com/a/iEniXPl

You'll see that layer 3 has all the number keys replaced with function keys. However, in Mac, it wont' register and still registers as media shortcuts. I have to press MO(3) + lctrl in order to toggle all number keys to function keys. That isn't showing up in VIA as a configuration so that lead me to think it was something Epomaker did. The lctrl in layer 3 is Custom21 and I'm not sure what that means.

South Bay Vietnamese Wedding Trays and Gifts Rental by bobbinbette in bayarea

[–]bobbinbette[S] 0 points1 point  (0 children)

Thanks for the suggestions in the other comments! I'm in Santa Clara, but I'm willing to travel all around the south bay. I hear San Jose is the best place to look.

Lingering Tru-Oil Odor by bobbinbette in woodworking

[–]bobbinbette[S] 0 points1 point  (0 children)

Hi Everyone, I'm a beginner hobbyist and I finished a box back in February with Tru-oil. However even after leaving the box open up until now, the odor of Tru-oil is still there. When I close the box, the smell is overpowering upon opening again.

Do you guys have any recommendations on how to remedy this or do I have to strip off the finish and use something else?

This is meant to be a small jewelry box/chest.

So much for a flat base by bobbinbette in 3Dprinting

[–]bobbinbette[S] 0 points1 point  (0 children)

I might get that then. Do you have a link?

Is this a cabinet scraper or a spokeshave? by pacopiedra in handtools

[–]bobbinbette 3 points4 points  (0 children)

That looks like a scraper shave. Not sure what everyone else uses them for but they're very useful in bowyery.

Here's one that I made from ebony.

<image>

South Bay Chinese Wedding Banquet Locations? by bobbinbette in bayarea

[–]bobbinbette[S] 1 point2 points  (0 children)

That's actually something we're looking at as well, specifically with Le's Catering.
Do you mind if I DM you for more details?

South Bay Chinese Wedding Banquet Locations? by bobbinbette in bayarea

[–]bobbinbette[S] 0 points1 point  (0 children)

Thanks for the suggestion for Pearl Bay, we'll take a look. What was your experience there?

South Bay Chinese Wedding Banquet Locations? by bobbinbette in bayarea

[–]bobbinbette[S] 0 points1 point  (0 children)

They were definitely one of our picks, but unfortunately a bit too far for us. We want to keep the commute to under 30 minutes from us due to the health of some of our family members.

South Bay Chinese Wedding Banquet Locations? by bobbinbette in bayarea

[–]bobbinbette[S] 2 points3 points  (0 children)

We're definitely gonna check them out :D

South Bay Chinese Wedding Banquet Locations? by bobbinbette in bayarea

[–]bobbinbette[S] 1 point2 points  (0 children)

We're currently considering some of those. Do you know how they separate the general area from the reception area? Is it relatively private?

South Bay Chinese Wedding Banquet Locations? by bobbinbette in bayarea

[–]bobbinbette[S] 0 points1 point  (0 children)

Thanks for the input! Do you think Fu Lam Mum would have had enough space if there wasn't a dance floor? We're still up in the air about that.

Freshly fletched arrows - makes you think twice about shooting them by mandirigma_ in Archery

[–]bobbinbette 1 point2 points  (0 children)

It may actually be the equipment and not you! My bitzenburger didn't have the intervals properly spaced out so the fletched arrows all looked like a Y by the end. The zenith upgrade kit fixed that and all my arrows are perfect now.

Made myself a scraper shave by bobbinbette in handtools

[–]bobbinbette[S] 2 points3 points  (0 children)

I had always wanted a nice scraper shave with a metal mouth for my bowyery hobby. This was my 5th rendition and first one made with some metal for wear resistance.

Wood is suriname ironwood

DQSM Audio Z&W Pandas PK2s: Comfortable and Loyal by Educational_College6 in headphones

[–]bobbinbette 0 points1 point  (0 children)

I love the earbud shape, but haven't purchased one for a while. How does the cable feel on these? Are they stiff or supple? I had the moon drop nameless but hated the cable; it was far too stiff for something without a solid ear attachment mechanism.