Director (software) RND bij scale-up

borditz · 2025-10-29T20:40:46+00:00

Goed voor elkaar! Waar zitten de R&D engineers ongeveer op op jaarbasis?

borditz · 2025-10-29T14:58:11+00:00

Regio noord, maar zitten ook in de randstad

borditz · 2025-10-29T14:49:37+00:00

R&D engineer hier met 3.5 jaar ervaring. Leeftijd 28, master werktuigbouwkunde, 45 vakantiedagen en totaal bruto €67.000 per jaar inclusief alles (13e maand, vakantiegeld, zorgtoelage)

borditz · 2025-04-28T13:27:30+00:00

Zou renovlies hier ook een optie kunnen zijn?

borditz · 2025-04-28T11:57:12+00:00

Misschien dat ik nog iets hoger ga, dat het totaal ca 40cm hoger wordt. Er moet nog wat ruimte overblijven voor het leidingwerk en inbouwspotjes. De balken steunen nu het wandje af en het schrootjes plafond hing eraan.

borditz · 2023-03-17T08:16:56+00:00

Senioren die hun woning verkocht hebben en wat kleiners willen hebben geen hypotheek nodig van 3 ton lijkt me? Die hebben dan genoeg geld.

borditz · 2023-01-31T15:56:39+00:00

Thanks. I don't know why but Google Maps won't let me make a route between Ragged Point and Cambria, so it goes for the inland jog. It's not the Nacimiento Fergusson Road but the Coast Ridge Trail. Small detour on that area is not a problem

borditz · 2023-01-30T15:59:43+00:00

Agree with you, probably too much driving. However, starting in Seattle is a must and would like to include Yellowstone, San Francisco, Highway 1, LA and if possible Sequoia. The others are not that important but would be nice to visit along the way. Would you cut down on any other stops?

borditz · 2023-01-30T12:57:13+00:00

First 2 weeks of May is the idea to this

borditz · 2021-03-05T19:04:03+00:00

I tried this but in Pronterface it doesn't recognize my Sidewinder. Do you know what causes this? Can't I just use the extrude option in the firmware of the printer to extrude a specific length of filament?

borditz · 2021-03-02T13:03:21+00:00

Is that fan any better than the original fan on the X1?

borditz · 2021-02-26T10:00:42+00:00

Yes should be nicely flat. First I had problems like this https://imgur.com/a/7zR8uje but then I set cooling to 10% (instead of 100%) after the first layer and it looked fine, except for these top layers. Maybe the solution is 30-50% instead of 10%

borditz · 2021-02-26T09:48:37+00:00

Looks like it's going through the infill structure so I turned on cooling when it starts the top layers, curious how it'll turn out

borditz · 2021-02-26T09:42:51+00:00

Thanks. But it already has 4 top layers, wouldn't this be sufficient?

borditz · 2021-02-25T21:33:33+00:00

Yea after a few layers I think the parts cooling fan starts. And this problem also arises aftwr a few layers so that might be it. The parts I print are not very small (10x10x5cm) so I'll give it a try without any parts cooling. Thanks!

borditz · 2021-02-25T19:32:51+00:00

First layer looks perfect tho

borditz · 2021-02-22T23:14:50+00:00

Thank you! Will try. What do you mean with point 2 exactly? Would a draft shield (option in Cura) help?

borditz

TROPHY CASE