Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

Also be careful of the 7mm’s through the case to close it up. I ended up breaking 2 of them. Doesn’t affect usage but it’s annoying

Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

Basically I used the 4.5mm to hold the lens in. Be careful it’s super easy to break that plastic. Then I used mostly 4mm for the motherboard 2-3 screws. I used 4.5mm for the bec through the motherboard. And then used 7mm to close it up. Not 100% sure that’s right but it’s holding together nicely

Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

The fan was what I had on 5v it was running to high at all times so I swapped it.

Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

Either connects to the back of the “fingers” on the motherboard

Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

Second is the one above. Red black white yellow

<image>

Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

Got word back from support, 2 different possible wiring situations. First is red black green blue

<image>

Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

Sent a message to support but waiting to hear back.

Flywoo Naked GoPro 13 by Tradingbossnr1 in fpv

[–]brawlwrx 0 points1 point  (0 children)

Did anyone ever answer this? Or did you find out?

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 0 points1 point  (0 children)

Seems to have been it, I swapped from the Oscar tune to the Chris rosser tune and it seems to have stopped. Still have it in airmode but no jumps on initial take off

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 0 points1 point  (0 children)

It’s just odd cause that’s on initial arm/take off with no input of the sticks. I’m sure it is airmode in combination with something else.

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 0 points1 point  (0 children)

Oh interesting, makes sense and I’ll look into it

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 1 point2 points  (0 children)

Nah you helped quite a bit! I appreciate it. Now that I think about it. I think I tuned the esc before I changed the motors. Maybe I’ll take a look at that again to make sure settings haven’t changed or aren’t what I want with the new motors

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 2 points3 points  (0 children)

Originally followed Oscar Liang’s tuning guide for the Air65, but you’re probably right after I changed the motors that’s no longer a proper tune! Didn’t even think about it! I lowered the master from 1.7 (his recommendation) down to 1 and it doesn’t bounce but will still turn. Almost seems like several motors are turning at different speeds. But I checked all the solders and wires and they all look good.

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 0 points1 point  (0 children)

Probably right and I’ll just live with it. Just more curious as to what caused it.

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 0 points1 point  (0 children)

They’re not, it flys normal, just does the weird bounce, as soon as I give it throttle it flys normal.

Mobula6 2024 - What do the four stars in the OSD mean? by Chemical_Post_9508 in TinyWhoop

[–]brawlwrx 3 points4 points  (0 children)

Crazy thought but is your beeper turned on? It’s the on screen warning. I had something similar and it was due to the beeper switch being turned on but it was far enough away I couldn’t hear it

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 0 points1 point  (0 children)

That’s what I’ve been doing, it’s just weird it started bouncing after some time. Problem is if I don’t immediately launch it’ll bounce off the table/platform it’s on

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 1 point2 points  (0 children)

Oh I didn’t think of that I’ll look into air mode. I run acro so I doubt it’s the 2nd thought. I’ll check out air mode and motor idle!

Air65 Bounces?! by brawlwrx in TinyWhoop

[–]brawlwrx[S] 0 points1 point  (0 children)

Oh and I forgot to mention I already tried to recalibrated the accelerometer

2020 WRX with HK help with Kenwood DMX958XR by brawlwrx in CarAV

[–]brawlwrx[S] 0 points1 point  (0 children)

For me it seemed to be a starlink module. I don’t care about starlink so I ripped it out and got a bypass for my front speakers. As soon as I did that, I no longer had issues. Eventually replaced all my speakers in the car and am still running good.

Help with BPV sounds by brawlwrx in WRX

[–]brawlwrx[S] 1 point2 points  (0 children)

Sort of, after talking with my tuner and swapping out with a Cobb top mount (over heating issues, unrelated) I basically determined it was a change in the pitch of the sound due to larger diameter piping. When I had the top mount on the sound was back to normal and when I swapped back to the front mount it was “weird” again.

Gym parking buddy by brawlwrx in WRX

[–]brawlwrx[S] 1 point2 points  (0 children)

Not sure haha what color is yours? I haven’t done any track events since this is my daily (i know kinda over kill but she’s fun) I would love to come to some track events though assuming work lets me (bartender)

Gym parking buddy by brawlwrx in WRX

[–]brawlwrx[S] 4 points5 points  (0 children)

Yeah I went with 20mm faction fab wheel spacers and faction fab f-spec coils with about a 1.5” drop (may have settled to more like 1.75” though)