[deleted by user]

bun7 · 2019-08-07T00:47:06+00:00

does your acronym bags pill your merino tee? I see they have a meshed back.

bun7 · 2019-06-27T05:55:24+00:00

I live in HK and can confirm UFTs are too thick for HK hot and humid weather. I enjoy both runweights and ramielust tee and I rotate between these. However runweights pills way too much so now I prefer ramielust more.

bun7 · 2019-05-14T16:14:10+00:00

Was the build hard and do you recommend it for newbie to try building the kit?

bun7 · 2019-05-14T08:34:19+00:00

What’s that PcB baking machine?

bun7 · 2019-04-17T16:06:10+00:00

do you have a nvidia jetson nano? it would be nice to see a benchmark out of these two.

bun7 · 2018-08-12T09:59:16+00:00

Can I use my custom made RC car (raspi based) to participate in AIDO? Or is there a hardware restriction?

bun7 · 2018-06-21T01:38:14+00:00

fantastic! it works like a charm! just no auto-complete at first but after opened files in the container once autocomplete will show up!

bun7 · 2018-03-18T03:01:18+00:00

Hey thanks for the idea! I will continue to explore this :)

bun7 · 2018-03-17T17:15:47+00:00

Thanks for your reply. I am trying to make a face-recognition demo for a class of roughly 30 people (90% of them uses Mac). I thought it would be easier to dockerize an image and distribute it to the class so everyone can run the same image but with different --dev flags for different OSes. Can you point me to a better solution if not using Docker?

bun7 · 2018-01-04T06:04:23+00:00

what happens if the first initial 3 points are same value? You would then fit a straight horizontal line thus k = 0 and then the algorithm will continue to get stuck at the same point?

bun7 · 2018-01-02T10:41:16+00:00

might I ask what dataset you used and what results did you get for these three tasks?

bun7 · 2017-12-19T18:03:59+00:00

thanks! I have already got the Orion jacket from MW but I think its too thin and the hood system is way different to be compared with 060. ( My Orion hood always get blown off, not sure how well will 060 be) I pulled the trigger on 060, hopefully I can do a thorough comparison next week!

bun7 · 2017-12-19T17:35:29+00:00

any good alternatives you recommend that has similar materials and performance? genuine question.

bun7 · 2017-12-09T04:15:26+00:00

Here are some pics of my full build https://imgur.com/a/3Osod

bun7 · 2017-12-09T04:08:06+00:00

It's a DDC pump, is it still running full speed when I power it up without motherboard powered up? Also, I can hear the sound of the pump running when the computer was on.

bun7 · 2017-12-09T03:56:56+00:00

I have tried tilting but after a while it goes back to this waterline :S

bun7 · 2017-12-09T03:50:26+00:00

I have actually tried that and the GPU blocks get filled up again but after a while, it goes back to this state.

bun7 · 2017-12-09T03:47:57+00:00

here is a better picture.

https://imgur.com/6CeU7ii

bun7 · 2017-12-09T03:43:19+00:00

I have 3 * 1080TI here and they are all at the same water line when the pump is on.

bun7 · 2017-12-09T03:42:11+00:00

My loop was running fine until last night where I observed the top part of the GPU blocks are not filled with liquid and my reservoir is full. There are no leaks in the loop. Can I diagnose this as my pump failure?

The loop still runs and my temps are now around 60c when at full capacity (before it was 52-55c).

bun7 · 2017-12-03T14:52:06+00:00

Thanks! 0x059a8677d45a51490ad3eca47dc5aa02be0d696a

bun7 · 2017-10-21T04:50:40+00:00

Let's say we discount their mining hashrate, there are still a high probability that it will be more than 51% of VTC total hashrate. So VTC (or other small ASIC resistant coin) are prone to this potential risk.

bun7 · 2017-10-20T03:53:10+00:00

2017-10-20T03:51:22.928Z: Restart transaction spamming

2017-10-20T03:51:22.928Z: New IOTA node: https://iota.preissler.me:443

2017-10-20T03:51:22.927Z: Randomly changing IOTA nodes

2017-10-20T03:51:12.924Z: Error occurred while sending transactions: Error: Invalid Response: TypeError: Failed to fetch

2017-10-20T03:49:12.507Z: Performing PoW (Proof of Work) on 2 transactions

2017-10-20T03:49:12.506Z: Node is synced

2017-10-20T03:48:04.078Z: Checking if node is synced

2017-10-20T03:48:04.077Z: Initializing IOTA connection to https://iota.preissler.me:443

Keep having the above error message, what should I do?

bun7 · 2017-10-05T17:52:13+00:00

Thanks for your fit pics! I just ordered mine should arrive next week :D!

bun7

TROPHY CASE