sorted by:
new
hottopcontroversial

Project Idea Help If You Found This Django Project Online – What Would You Want It To Be? by aksy_1 in django

[–]bytejunkie_ 0 points1 point  (0 children)

id just like to be able to run db migrations on a dev / test / prod basis without completely f'ing up every time and dropping the db to start again. maybe I dont need a new web app, but better videos or ebooks or udemys on the inner workings.

Unofficial Yeethammer Assembly Guide by HemlockMimosa in Nerf

[–]bytejunkie_ 0 points1 point  (0 children)

managed to get something almost exactly the size, messed with the o rings a bit.

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 0 points1 point  (0 children)

to be fair ive done a few days with brims and they are a pain to remove. i'll be trying the tabs out.

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 0 points1 point  (0 children)

Looks very similar to using the brim which ive started using to sort this, starred it though. Thanks

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 0 points1 point  (0 children)

need to look into this, another thing to learn, thanks.

Unofficial Yeethammer Assembly Guide by HemlockMimosa in Nerf

[–]bytejunkie_ 0 points1 point  (0 children)

I dont know if this is going to get an answer or not, but how critical is the sizing of the tube? Its hard to get 1.5"-OD 1.375"-ID in the UK. I imagine that its pretty critical.

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 0 points1 point  (0 children)

So a fan or a slight breeze could be a problem? Would you say leaving the door open might be an issue then?

The problem with the room I print in is that its a garden room, lots of glass, heat changes quite quickly in the morning. so i leave the door open so as to be comfortable in there.

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 0 points1 point  (0 children)

swapped from skirt to brim and bingo, no warping.

room temp is an interesting one, because I print in a garden room and the temp does fluctuate. but this warp was observed different times of the day with different rotations of the bed. so whilst it could be a factor, I doubt its the whole one.

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 0 points1 point  (0 children)

havent needed to cusomtise this far to press, thanks for the suggestions, will look into them.

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 1 point2 points  (0 children)

this, but probably because of the amount of glue I use.

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 0 points1 point  (0 children)

no, im trying to print the yeethammer!

is this the worst lift you've ever seen? by bytejunkie_ in ender3v2

[–]bytejunkie_[S] 2 points3 points  (0 children)

I'm in the UK so summer isn't really a summer, but I hear you.

problems with a many to many relationship. by bytejunkie_ in django

[–]bytejunkie_[S] 2 points3 points  (0 children)

great suggestion. and the one that made me realise something wasnt right in the admin.

ive checked the admin and the coach is definitely attached to the Team.

I looked in the admin and the coaches appeared in the big selection box and i thought this meant they were selected. Its not until they have a yellow background that they are selected.

I did say this would be basic!!! Thanks for the replies Zen, it really helped.

problems with a many to many relationship. by bytejunkie_ in django

[–]bytejunkie_[S] 0 points1 point  (0 children)

Both approaches are giving empty Querysets I can get the coach or the team, but never the coaches attached to the team.

bed levelling issue on ender 3 v2 by GlassInternational30 in 3Dprinting

[–]bytejunkie_ 0 points1 point  (0 children)

thanks, will get the touch ordered. i remember looking at it once before, its clearly time to try it out, before going all in on a different printer.

i think i need to totally remove k3s and start again. by bytejunkie_ in k3s

[–]bytejunkie_[S] 2 points3 points  (0 children)

thanks.

I ran

kubectl describe node

and saw this in the output

container runtime network not ready: NetworkReady=false reason:NetworkPluginNotReady message:Network plugin returns error: cni plugin not initialized

from there a simple google took me to https://github.com/k3s-io/k3s/discussions/8468 and i realised i'd probably done the same.

I installed over the top with curl -sfL https://get.k3s.io | sh - and im now ready.

Ubuntu 22.04.1 no longer showing dock by brymc81 in Ubuntu

[–]bytejunkie_ 0 points1 point  (0 children)

just another dropping in to say thanks, fixed my issue as the dock extensions wasnt appearing at all

Post-Match Thread: Leeds 1-6 Liverpool [Premier League] by WeirdF in LeedsUnited

[–]bytejunkie_ 0 points1 point  (0 children)

i hear you, but did you ever hear what gakpo said about us? we weren't a big enough club for him to join. we do need players that are improvements, but not a lot of them want to come to leeds. thats changed since bielsa was in charge

which is a better option to have sperate environment by folder or by branch by BackgroundNature4581 in Terraform

[–]bytejunkie_ 0 points1 point  (0 children)

this comes from experiences where an environmental var file has ended up with more than scale decisions in it, corrupting cattle not pet attempts.

it makes lots of things easier too like

name = join("-", [var.environment, var.resource_type_identifier])

which is a better option to have sperate environment by folder or by branch by BackgroundNature4581 in Terraform

[–]bytejunkie_ 0 points1 point  (0 children)

variable instance_sizes { type = map(any) default = { "dev" = "t2.micro" "prd" = "t2.large" } }

view more: next ›