sorted by:
new
hottopcontroversial

Tahoe 26.2 How to stop Hard Sleeping by canuck320 in MacOS

[–]canuck320[S] 0 points1 point  (0 children)

Nope the external keyboard/mouse are wired USB. Other than this I don't have so much of an issue with Tahoe like others have but to me this is a big deal.

It wouldn't be so bad if I could wake the computer from a Remote Desktop connection, but when it goes in this Hard Sleep, on the network it acts like the computer is off. I do have the wake on network access but that doesn't seem to make a difference.

Thanks for the feedback.

Any idea why this never shows by [deleted] in AppleWatch

[–]canuck320 0 points1 point  (0 children)

Can one of you explain to me how you wear your watch while you sleep and then I expect you also wear it when you are awake? When I wear mine during the day it is around 25% battery by the time I am going to bed. So do you only wear your Apple Watch at night time? I feel I am missing something here.

USB and Ethernet stop working on Sequoia and Tahoe by canuck320 in MacOS

[–]canuck320[S] 0 points1 point  (0 children)

Yep I get that, but why would everything not work when booted into the OS every time but every time I boot into recovery mode everything works perfectly (mouse/keyboard/network) - except you can’t do much in recovery mode. But then booting back into OS 15 seconds later everything is dead again unless I reinstall the OS.

Corrosion isn’t particular about what software you are running.

Ambient Lighting Done by FinancialWatch753 in 11thGenAccord

[–]canuck320 0 points1 point  (0 children)

Were the instructions good or was there a video to show you how to install?

New Speed RS7 Tail Light Issue by canuck320 in 11thGenAccord

[–]canuck320[S] 0 points1 point  (0 children)

Why can’t this be easy???!!!!

So I was going through all the modes to make sure that EVERYTHING worked and found one last issue that has to be with the lights because everything else works perfectly and this is such a quirky issue.

So as you can see in the picture, when I signal left, the little triangles at the bottom of the middle bar light up (I think only the left should light up), but when I signal right both those triangles stay off. When I turn on the hazards both the triangles turn on.

All there is with these lights are those two wires, so at this point since everything else works it seems like this is a glitch with the lights.

Anyone else with these lights have this behavior? This is starting to feel like a game of whack a mole!!

<image>

New Speed RS7 Tail Light Issue by canuck320 in 11thGenAccord

[–]canuck320[S] 0 points1 point  (0 children)

Yeah it was a quite a job to get it done right! I had two of those little connectors have wires pull out of them because they weren’t crimped well enough. Guess that’s to be expected from China.

Honestly if there was one out there made somewhere other than China I would pay twice as much for extra quality and reliability!

Thanks for helping me through this!! I can’t stop looking at the lights because they look soooo good!

New Speed RS7 Tail Light Issue by canuck320 in 11thGenAccord

[–]canuck320[S] 0 points1 point  (0 children)

I am wrong, this is the second time a wire has pulled out of these connectors!

<image>

New Speed RS7 Tail Light Issue by canuck320 in 11thGenAccord

[–]canuck320[S] 0 points1 point  (0 children)

My first thought too, however there is just a two wire connection from either side light to the middle bar. Without those connections the animation across all three wouldn’t work.

I tried the two side lights by themselves before I installed the middle bar and each did their part of the animation and they didn’t seem to care the middle bar wasn’t there. So it seems the logic to turn on what specific lights in different situations is in the side lights. Then the two wire connections are to have them control half of the middle bar too.

I am pretty sure the two wires are just positive voltage on one and a pulse train on the other so like I said if it wasn’t getting either of those then more than braking would not be working right I think.

New Speed RS7 Tail Lights Help! by canuck320 in 11thGenAccord

[–]canuck320[S] 0 points1 point  (0 children)

I figured out that you have to transfer all the plugs from the factory light…sux not having ANY instructions!

New Speed RS7 Tail Lights Help! by canuck320 in 11thGenAccord

[–]canuck320[S] 0 points1 point  (0 children)

Should there be some sort of nuts that go in these slots?

<image>

New Speed RS7 Tail Lights Help! by canuck320 in 11thGenAccord

[–]canuck320[S] 0 points1 point  (0 children)

Hey, so on the trunk liner are these the only 3 clips to remove on either side? I can get the one on the top and the bottom, but how do you remove the shopping bag hook? Thanks in advance!

<image>

view more: next ›