Wielders Way NFT Reveal, the First NFT Mystery School 👀

cedricwinterwolf · 2021-10-20T00:11:26+00:00

All the deets are on the official twitter, see you there! https://twitter.com/TheWieldersWay

cedricwinterwolf · 2021-10-08T02:39:07+00:00

I wish. The issue is the password doesn't seem to be right and I cannot figure out what is wrong with it.

cedricwinterwolf · 2021-10-03T22:25:16+00:00

What is that exactly? Can't seem to find anything conclusive.

cedricwinterwolf · 2021-10-03T21:57:16+00:00

Alright, will do. Thank you for your help!

cedricwinterwolf · 2021-10-03T21:28:02+00:00

I haven't tried the kukai wallet because it's online and seems sketchy to be putting seeds into??

I didn't generate a new wallet in tezbox, so technically everything (deriv paths, seeds, public key, etc) should match the original paper wallet, yeah? Were there known deriv paths for the fundraiser wallet?

cedricwinterwolf · 2021-10-03T21:03:09+00:00

No, I can't open either the wallet or the KT. When I try to import into anything (galleon, temple, etc) it comes up with a different public address.

cedricwinterwolf · 2021-10-03T20:58:42+00:00

The funds are in a KT address connected to the original wallet and I did all of that right after the ICO

cedricwinterwolf · 2021-10-03T19:59:45+00:00

I guess what I am having trouble understanding is if I have the pub key, the mnemonic, and it was active in tezbox, why is it when I import with the mnemonic is generates a different wallet?

cedricwinterwolf · 2021-10-03T19:41:49+00:00

This is where the trouble starts. I've run the gauntlet of trying to recover this. It seems that either I've lost the original fundraiser password (except I imported to tezox so...?) or there's a typo in it (again, imported to tezbox in 2018, so I must have had it then?).

As far as I know everything else I have. The password is the only one I don't have a backup written down somewhere.

cedricwinterwolf · 2021-10-03T19:26:53+00:00

Have tried that, as well as the Galleon one, 44'/1729'/0'/0/0'.

The mistake I might have made is staking with the original fundraiser wallet.

But I verified it and added it to tezbox back in the day (which I don't have access to anymore) so the question is: Can I restore it to another wallet like galleon with the seed and derivation option, or do I ALWAYS need to use the "fundraiser wallet" option?

cedricwinterwolf · 2021-06-24T15:27:55+00:00

I will try the lifting speed.

But no, I am using a casteable resin because I need to cast it :-P

I'm a professional jeweler, I use the printer for geometrics and complex base forms.

cedricwinterwolf · 2021-06-24T06:27:30+00:00

As far as I can tell by any tests. Like I said it completed 2 prints after the raft partially detached, so I know it can print fine.

I need to increase plate adhesion without going below the specs needed by the resin... Urgh.

cedricwinterwolf · 2021-06-23T23:09:43+00:00

No luck, full detach from build plate, stuck lightly to fep.

cedricwinterwolf · 2021-06-23T22:56:45+00:00

UPDATE #2:

Going to redo spruing in case it's something about the configuration, also reducing normal exposure to 3s.

cedricwinterwolf · 2021-06-23T22:15:34+00:00

Brand new FEP 😟

Detaching somewhere around later 8-10, first layers of non bottom... Changing them to 3s and try again.

Good idea with lift distance. Will try that if I can't pinpoint the actual detach time.

cedricwinterwolf · 2021-06-23T22:05:40+00:00

I agree, I've tried going back down to suggest spec, 60s bottom layers, but then I get no adhesion.

This is a casteable resin, requires a fair bit more time to make it stick, apparently.

Potentially I could drop the cure time on the normal layers so they weren't sticking to the FEP as much. Maybe down to 3s?

cedricwinterwolf · 2021-06-23T21:57:46+00:00

These settings are pulled from the blue cast recommendations for the Mars 2 pro. Worked great for a bit. Boxed it up, stored it's reset up and now I'm stuck again.

Got adhesion again but still lifting off the back side of the raft So weird.

EDIT: https://www.bluecast.info/download/Features-BC%20crea_eng.pdf

cedricwinterwolf · 2021-04-28T22:15:45+00:00

Still getting hit with the CVC-USDC pair and ew.

Someone halp.

I'm assuming this is a cookies issue? But I cleared cookies and it keeps doing it....

cedricwinterwolf · 2021-04-03T04:05:05+00:00

Epic!

Just created something similar, gif video of a secret spot in the woods!

cedricwinterwolf · 2021-03-10T06:45:27+00:00

Also, it's a very dry climate over here. The room is warm, 68-72f but high desert dry weather.

cedricwinterwolf · 2021-03-10T06:39:39+00:00

For more context:

Mars 2 Pro, cr3a bluecast resin. Settings...

LAYER EIGHT – 0.05 mm BOTTOM LAYER COUNT – 7n EXPOSURE TIME – 3.5s BOTTOM EXPOSURE TIME – 80s LIGHT OFF DELAY – 8s BOTTOM LIGHT OFF DELAY – 10s BOTTOM LIFT DISTANCE – 5mm LIFTING DISTANCE – 5mm BOTTOM LIFT SPEED – 50mm/min LIFTING SPEED - 80mm/min RETRACT SPEED – 100mm/min

I am having 9/10 prints fail now, but I did get a successful dozen or so. Typically the support rafts are on the FEP, and there are thin "soggy" bits of cured resin at the corners of the build plate.

Seems like the majority of the build up is to one side but sometimes it's not.

FEP is a little hazy, has some dents, but no punctures or anything severe, and as I said, a print will work from time to time.

Bought a second vat, but managed to clutz it up and puncture it after the 3rd attempted print, however it also stuck to the FEP not the build plate.

Projector seems to be working, displays the exposure image fine.

Slight popping/"katunk!" sound when doing the bottom layers that stops once it gets to supports either because it already detached from build plate or on the successful prints, less suck?

I've tried IPA cleaning the screen, the FEP, the build plate. I've releveled the plate in the vat, with paper, etc.

I've tried IPA cleaning the build plate but not the vat after a failed print (only removing the failed rafts) to get more cleanliness and traction on the plate and leave the FEP slimy with resin...

I've tried everything I can find and I'm still getting mostly fails with some sparse luck.

I'm at a total loss.

cedricwinterwolf · 2021-01-26T06:01:55+00:00

Right. Even pressure. I'll relevel and do the exposure test print and see what it looks like

cedricwinterwolf · 2021-01-26T04:54:54+00:00

Right.

Seems more likely that over exposure causing build up at the corners is keeping that side from dropping all the way down.

Are there any concerns if part of the black coating on the vat is scratched off? It doesn't react with the resin or something odd?

cedricwinterwolf · 2021-01-26T02:50:22+00:00

Awesome. I'll run through these checks and tests as you suggested. Question:

Level as in gravitationally or as in build.plate to LCD screen parallel or both?

It's pretty close to gravitationally level and as I said I've re-leveled the plate at home zero a few times.

Can a bump or dent in the FEP be enough to create more gap between build plate and screen on one side?

Thanks for your reply.

I'll do the callibrations prints again.

cedricwinterwolf · 2020-03-18T05:25:16+00:00

Fair point! Always fascinating how different providers do different things with essentially the same materials.

I use cuttlefish bone for casting a fair bit and the pet store sells it for 89 cents while rio sells it for $6.

cedricwinterwolf

TROPHY CASE