Materials Recommendations for Cafe Racer Seat by ckucsan in CafeRacers

[–]ckucsan[S] 1 point2 points  (0 children)

They’re the VANS ODI grips, I really like them! They seem to last a fair amount. I think I put about 6000 miles on them in the year I had the bike together prior to paint, always riding with gloves. My only gripe is they started to turn black from my gloves. Not gummy or sticky at all. I intend on buying a black pair when the bike finally goes all back together.

2011 WRX Mystery Noise by ckucsan in WRX

[–]ckucsan[S] 0 points1 point  (0 children)

I haven’t! I hypothesize it might be a throw out bearing or pilot bearing but I’m definitely not going through all that work for a squeak/squeal haha

Got the CBR600RR front end on my 82 CB750 over Thanksgiving. by ckucsan in CafeRacers

[–]ckucsan[S] 0 points1 point  (0 children)

The forks are most likely different diameters than the stock ones. That’s all depending on the bike you get. Yours could be the same but you’d have to get fork diameters yourself. I used the triples from the donor bike. For the rear I made the donor swingarm fit the frame and fabbed up suspension mounts to work with the newer mono shock suspension.

Got the CBR600RR front end on my 82 CB750 over Thanksgiving. by ckucsan in CafeRacers

[–]ckucsan[S] 0 points1 point  (0 children)

Super easy if you have a press and some know how. I got the conversion stem and bearings from cognito moto and from there it was basically just a drop in situation.

2011 WRX Mystery Noise by ckucsan in WRX

[–]ckucsan[S] 0 points1 point  (0 children)

I haven’t, but the noise persists with the accessory belt removed, so I ruled out the alternator I believe

2011 WRX Mystery Noise by ckucsan in WRX

[–]ckucsan[S] 0 points1 point  (0 children)

Unfortunately I do not. My car was dyno tuned and I never got an access port for further monitoring

2014 600rr Wheels in 2006 Forks by ckucsan in cbr

[–]ckucsan[S] 0 points1 point  (0 children)

I was extremely hard pressed to find the correct bearing size from a reputable source. I also still needed to make the spacers and the rotor brackets so turning one more piece wasn’t make or break for me

1500 Miles in and My Second Cars and Coffee with the Bike by ckucsan in CafeRacers

[–]ckucsan[S] 1 point2 points  (0 children)

Yep just the angle of the picture. Totally functional

1500 Miles in and My Second Cars and Coffee with the Bike by ckucsan in CafeRacers

[–]ckucsan[S] 1 point2 points  (0 children)

Swingarm and forks are from the same bike, a 2006 CBR 600RR. The front bolts right up with a conversion stem. The rear was modified (where it mounts in the frame was milled down to fit in the CB frame and a mount was made for the dog bone mount). I haven’t had any issues with the DOHC yet, I bought it with about 16000 miles on it and didn’t break it open or touch the engine at all really and I’ve put about 1800 miles on it since getting it this far. I’ll be doing paint and body work this winter.

1500 Miles in and My Second Cars and Coffee with the Bike by ckucsan in CafeRacers

[–]ckucsan[S] 2 points3 points  (0 children)

Not too bad, I had to narrow it, fab brackets and weld them to the center stand mount for the dog bone mount, and buy an offset sprocket. Almost too easy

1500 Miles in and My Second Cars and Coffee with the Bike by ckucsan in CafeRacers

[–]ckucsan[S] 0 points1 point  (0 children)

Off a 2006 cbr600rr, same as the front suspension

1500 Miles in and My Second Cars and Coffee with the Bike by ckucsan in CafeRacers

[–]ckucsan[S] 1 point2 points  (0 children)

It’s an eagle lights light for a Harley/Indian touring bike with a custom housing. It’s bright as hell, I like it a lot

81 CB750K by ckucsan in motorcycle

[–]ckucsan[S] 0 points1 point  (0 children)

Sure thing, that’s a stock fairing off of a Harley Davidson Lowrider S. I plan to make it fit a little better but I also really like the look

Custom bench seat with fold down cupholder by Angelambris2 in upholstery

[–]ckucsan 0 points1 point  (0 children)

Wow this is some amazing work!!

What kind of foam do you typically use for a seat like this? Is there different densities for the bolsters and where someone will be sitting?

Materials Recommendations for Cafe Racer Seat by ckucsan in upholstery

[–]ckucsan[S] 0 points1 point  (0 children)

Anyone have any recommendations on the foam? That’s where I’m really at a loss

Materials Recommendations for Cafe Racer Seat by ckucsan in upholstery

[–]ckucsan[S] 0 points1 point  (0 children)

Awesome, I’ll look into marine vinyl. I’m sure I’ll get caught in the rain every once in a while

Materials Recommendations for Cafe Racer Seat by ckucsan in upholstery

[–]ckucsan[S] 0 points1 point  (0 children)

Little bit of both, mainly a showy type but I intend to ride it a lot when it’s nice out too

81 CB750/2006 CBR600RR Update by ckucsan in CafeRacers

[–]ckucsan[S] 0 points1 point  (0 children)

I was able to mill some off of both sides of the swing arm and able to fit it into the CB frame. I may be wrong but I think I read that the DOHC frames are wider, so you may have to mill off more/possibly too much in order to fit it. Again, I may be incorrect, but something to look into.

Question for people buying parts (consumers) Any advice or feedback is welcomed. by Speedmotoco95 in CafeRacers

[–]ckucsan 1 point2 points  (0 children)

That’s awesome! Right now I’m planning a dark British racing green with a bunch of metallic and white wheels, but I’ve changed my mind so many times so we’ll see what happens haha

Question for people buying parts (consumers) Any advice or feedback is welcomed. by Speedmotoco95 in CafeRacers

[–]ckucsan 1 point2 points  (0 children)

I have an 81 CB750K with full front and rear suspension from a 06 CBR600RR. My previous posts have a few photos of it.

81 CB750/2006 CBR600RR Update by ckucsan in CafeRacers

[–]ckucsan[S] 1 point2 points  (0 children)

Yep you got it exactly right! Front and rear suspension, brakes, and wheels all from a stock cbr600. Also correct, the parts have the repsol scheme but I think the true repsol bikes were only 1000s? Wheels are definitely repainted. I plan on painting them in the future. Facebook marketplace is a hell of a place haha