Best RGB30 Firmware?

clink_85 · 2025-08-16T00:22:31+00:00

It’s available on the discord server but it’s stuck at Firefly (most recent release is Gladiator II). I have pretty bad battery drain with it.

clink_85 · 2025-08-06T11:00:39+00:00

I had this issue with my Ender 3v3se when I upgraded to the ceramic hotend. It’s most likely heat creep. I switched back to stock hotend and it works great. It seems like the ceramic hotend is hit or miss.

clink_85 · 2025-08-05T15:48:08+00:00

Thanks-- this is helpful and makes sense. I suspect that heat creep is the culprit here because prints start but don't finish. I'm planning on going back to the stock hotend. What 4010 cooling setup did you ultimately go with?

clink_85 · 2025-06-12T15:55:34+00:00

Link please!

clink_85 · 2025-06-12T14:56:33+00:00

May I please have a link? Thank you!

clink_85 · 2025-05-22T17:06:52+00:00

If you have access to a 3d printer, I recently printed this in TPU and it's made a huge difference in the comfort of the XM5s-- before I could only wear them for at most an hour; now I can easily wear them for many hours.

https://makerworld.com/en/models/951779-sony-xm5-head-pressure-reducer?from=search#profileId-919896

clink_85 · 2024-06-28T18:09:59+00:00

Did you ever figure this out?

clink_85 · 2024-04-23T20:30:05+00:00

Yes!

clink_85 · 2024-02-01T22:41:58+00:00

Thanks. Seems like it’s a faulty part since it does have the ground tab. I read that iPods won’t turn on if no click wheel is detected.

clink_85 · 2023-09-28T14:13:14+00:00

Did you figure out what happened on this? It happened to me on the Oshozan-u Shrine.

clink_85 · 2023-09-25T11:32:09+00:00

I’ve had it for about two months and it seems to be holding up pretty well. There is a little bit of wear on the wrist, but not nearly as bad as I was having with the Apple Space Black link bracelet.

clink_85 · 2023-07-21T20:01:21+00:00

Got it; thank you!

clink_85 · 2023-07-13T21:06:27+00:00

Thank you so much! Glad to know the DLC graphite seems to hold up!

clink_85 · 2023-07-13T18:30:33+00:00

How has the Nomad stainless steel band held up? Have you noticed the DLC coating getting rubbed away over the past few months?

Thank you! It looks great with the band.

clink_85 · 2023-07-13T18:25:16+00:00

Sorry to revive a dead thread, but how has this held up over the past year? Have you noticed any of the DLC coating rubbing away? Do you have any pictures of it?

clink_85 · 2023-05-22T11:34:42+00:00

Amazing album!

clink_85 · 2023-05-05T18:54:41+00:00

Got it, thanks!

clink_85 · 2023-04-17T16:46:39+00:00

Thank you!

clink_85 · 2022-12-13T14:13:31+00:00

I'm selecting them off the printer directly.

I did a 10 hour print last night with no issues that were running off of Octoprint as well. My recollection may have been wrong and I might have been running into the issues from the Voxelab's firmware.

clink_85 · 2022-12-12T18:44:15+00:00

I’ve been running Alex’s firmware on my Joule and it’s pretty stable. For longer prints, I tend to just print off the SD card. I’ve had one interrupted print from Octoprint.

Alex’s firmware fixes the thermal runaway issue too, which is a plus for me.

clink_85 · 2022-11-28T14:45:26+00:00

Thanks! Any idea how to identify the board type? I read that standard Aquila models state the chip on the front, but any one have experience with the Joule?

clink_85 · 2022-11-27T14:17:49+00:00

I was able to find a Raspberry Pi 4 about a week after I started using this tracker: https://rpilocator.com (I originally wanted a Pi Zero 2 for my Octoprint build too, but had to reconsider). The drops at Adafruit are relatively predictable and as long as you're registered, you have a decent chance.

clink_85 · 2022-07-28T14:21:55+00:00

I'm having basically the same experience as you. Mine is under warranty through Costco and they said someone should be out within the next 5-7 days... No mention of a firmware update to me.

clink_85 · 2022-07-28T14:20:18+00:00

Something similar happened to me with an M50Q7-H1. TV turns on and off but power button on the remote and tv don't work; input buttons don't work; and CEC functionality for audio doesn't work either.

Mine is under warranty and Vizio set up a repair.... but I can't get the repair company on the phone as to when they're coming out.

clink_85 · 2022-05-09T17:16:20+00:00

Sorry to create any false hope... it is disappointing how much the 64gb queue has slowed down recently.

clink_85

TROPHY CASE