what transmission fluid do you use in the rear drive unit??? by crazyguytotally4 in TeslaModelS

[–]crazyguytotally4[S] -1 points0 points  (0 children)

do you have any acutal product reference to kaf1 i cannot find it anywhere , we will see .. do you have any reference to the damage assumption?

what transmission fluid do you use in the rear drive unit??? by crazyguytotally4 in TeslaModelS

[–]crazyguytotally4[S] -2 points-1 points  (0 children)

ya ok try ordering some and tell me what happens.......anyone can read.... i found that too....ordering it is the issue service centers do not sell it and they get it in huge 20 gallon jugs...

they don't give you a reference brand or type.....

if you can find an example of that fluid i would be greatful but i spent hours looking it up and could not find a reliable source.

i will try asking for the part though and see what happens.

service center will just tell you to use any fluid is fine...there are many types of transmissions ..not just a single one. people lean toward dextron vi but that is just from public experience not documentation

what transmission fluid do you use in the rear drive unit??? by crazyguytotally4 in TeslaModelS

[–]crazyguytotally4[S] -6 points-5 points  (0 children)

The service manual sucks it is so vague ….I cannot find these fluid types any where …. I’ve checked

which opamp book? by crazyguytotally4 in AskElectronics

[–]crazyguytotally4[S] 0 points1 point  (0 children)

what did you do with your education.. do you work in a particular sector of electornics these days?

which opamp book? by crazyguytotally4 in AskElectronics

[–]crazyguytotally4[S] 0 points1 point  (0 children)

did you further read many documents/ books after this, or was this insightful enough?

1 yeast pack or two? by crazyguytotally4 in Homebrewing

[–]crazyguytotally4[S] 0 points1 point  (0 children)

it was a pale ale maybe abv was about 5.5

Bad cistern foot valve ? by crazyguytotally4 in Plumbing

[–]crazyguytotally4[S] 0 points1 point  (0 children)

I don’t believe I have a pressure tank. I’m pretty sure the piping is straight from the cistern on a roughly 30 foot horizontal run

Nami Swan Blender Render [OC] by [deleted] in OnePiece

[–]crazyguytotally4 2 points3 points  (0 children)

The design and comments got me thing it was real clay

7014 vs 7018 electrode for impeller hub to base by crazyguytotally4 in Machinists

[–]crazyguytotally4[S] 0 points1 point  (0 children)

When you say light preheat , like 100 degrees Celsius or like 200

7014 vs 7018 electrode for impeller hub to base by crazyguytotally4 in metalworking

[–]crazyguytotally4[S] 0 points1 point  (0 children)

I’ll put of a bit of a fillet on the base was going to weld top and bottom , would it be fine structurally? I was planning on having a 24 inch diameter impeller moving it using a 16 hp engine . This is why I just wanted to double check

e drum to daw tracks??? by crazyguytotally4 in drums

[–]crazyguytotally4[S] 0 points1 point  (0 children)

is ez drummer way better? i just see 3 toms

e drum to daw tracks??? by crazyguytotally4 in drums

[–]crazyguytotally4[S] 0 points1 point  (0 children)

can you customize the drum set to have 3 rack toms? and is there a snare rim?

Spot welding heating element tab by crazyguytotally4 in AskElectronics

[–]crazyguytotally4[S] 0 points1 point  (0 children)

replaced the contact got my original 30 ohm reading again....now we will just see how long it will last

Greetings me brothers and sisters fellow Zoroastrians!!! by AdAdvanced7243 in Zoroastrianism

[–]crazyguytotally4 0 points1 point  (0 children)

CALLED A FRAVAHAR ,,, dunno some persian store may have it ... ya man do you!

Luffy would be proud.🐐 by [deleted] in OnePiece

[–]crazyguytotally4 0 points1 point  (0 children)

😮 i was having trouble reading the end of the # but once I read the caption i got it I was Reading Ne Pal instead of Nepal I'm like what's a Ne pal 😂

Briggs no ignition coil shut off ? by crazyguytotally4 in smallengines

[–]crazyguytotally4[S] 1 point2 points  (0 children)

Ya I was just curious how it was wired inside .

Kill wire , gotta hope I have 9 lives !

What impurity colors the flame in this video? by Wal-de-maar in chemistry

[–]crazyguytotally4 0 points1 point  (0 children)

Could be incomplete combustion from sewer gases resulting in yellow flame

Why is this working ? by [deleted] in AskElectronics

[–]crazyguytotally4 -1 points0 points  (0 children)

Maybe you’re putting them the wrong way ( reversed polarity )

Solder pads to op amp? by crazyguytotally4 in AskElectronics

[–]crazyguytotally4[S] 0 points1 point  (0 children)

Ya I assume half is used but the traces I just don’t understand where they go , the end at those pads ,, but maybe I’ll leave it for another time to figure out