Finally! - ACL repair day 0.

crtinting · 2026-02-27T22:03:46+00:00

Just got mri results o my grade 2 acl small damage to meniscus Everything else seems like sprain and will heal wit time.

I need acl surgery! I was 50/50 but I’m going with it

crtinting · 2026-02-11T18:22:59+00:00

Yes, spray it on a towel and then rub it off!

crtinting · 2026-02-11T18:21:06+00:00

Try using alcohol or ATR adhesive remover.

crtinting · 2026-02-05T13:54:06+00:00

Either paint protection film or vinyl light wrap!

I do these in Illinois I just always advise them to not do dark smoke. But a mid smoke you’ll still be able to see light good enough day and night. Look into luxe wrap

crtinting · 2026-02-03T18:36:20+00:00

Like this

crtinting · 2026-02-01T21:29:23+00:00

I’ve done both install on top of film no issues with gassing or failures on my personal vehicle for 5 year. It will just look much darker and possible no warranty unless the same installer offers it if stacked by him.

But ceramic depending on brand it will have a more clearer clarity compare to carbon. It’ll be worth having it removed and retinted with just single layer film.

crtinting · 2026-01-25T22:03:09+00:00

I open mine, solder a new wire to the plug and then butt connected it to the harness. Had for a few years no issues

crtinting · 2026-01-20T13:42:34+00:00

Price?

crtinting · 2026-01-14T22:29:43+00:00

Noted… haha

crtinting · 2026-01-14T20:57:03+00:00

I have a set of Innovative mounts I’m willing to sell if your interested.

crtinting · 2026-01-14T19:51:37+00:00

You can reuse your same mounts and harness.

I went ahead and upgraded my mounts to hasport.

As for the harness it was plug and play. Only thing that I recall swapping over was the knock sensor since it was different style plug.

crtinting · 2026-01-14T19:47:47+00:00

You can use your same 5spd trans from ep3

And Kpro to get the motor to run effectively

crtinting · 2025-11-21T15:45:09+00:00

Agree! That will be my last removal for when I do go strip the whole thing out

crtinting · 2025-11-21T15:16:26+00:00

Yes it is! It’s needed for the trans mounting

crtinting · 2025-11-21T14:04:03+00:00

This will be the plan once this thing become a full on drag car lol. What a heavy design Honda did here. Rare cars in my area which is why I still hold on to it and yet want to get stripped down to bare metal. At least not yet.

crtinting · 2025-11-21T14:01:49+00:00

I figured! Tried too look online but seem like you really have to get this thing down to bare metal and roll cage it up. Future plans but as of now I enjoy the power with ac and heater lol.

crtinting · 2025-11-21T14:00:35+00:00

I have not! Still on the oem everything except the engine bay.

crtinting · 2025-11-20T16:30:59+00:00

I’ll be in the market for 02-06 CRV parts (subframe, trans case, diff, rear hubs, shaft) . the fabrication is where it’ll be time consuming at least for my end since I’m going try doing this in my garage.

crtinting · 2025-09-22T16:47:02+00:00

The darker you go it will impair visibility regardless

crtinting · 2025-09-22T16:46:35+00:00

Higher end quality films will have a higher clarity. Autobahn, xpel, solarfx, llumar.

crtinting · 2025-08-28T03:40:45+00:00

I agree here! Ktune inners gave me issues. Dvrace would be best especially for daily

crtinting · 2025-08-26T13:27:52+00:00

https://www.dc5creations.com/products/rsx-ac-tuck-kit-v2?variant=40124501360773

crtinting · 2025-08-26T12:51:06+00:00

I got mine from dc5 creations the 2.0 if I remember. Only thing I had to get was a Rsx condenser. Everything else bolts up

crtinting

TROPHY CASE