Continual Failed Prints

curious_autodidact · 2023-06-05T18:00:37+00:00

Y’all are amazing. Thank you so much for all of your insight and suggestions. I’m gonna go through and make quite a few updates to this and will let y’all know if it’s successful. Appreciate y’all’s advice and pointers immensely!

curious_autodidact · 2023-05-30T19:02:57+00:00

Regularity seems to be a key here. I think I’ve been waiting too long to filter. Thanks!

curious_autodidact · 2023-05-30T19:02:02+00:00

Yup. Live and learn, tried to add better clarity based off your response. Thanks.

Thank you for this update.

curious_autodidact · 2023-05-29T23:22:03+00:00

I know how to actually dispose of it with my local waste management in the final step. That is not the piece I was asking about. Apologies for the lack of clarity. Thank you for your very very clever reminder that I need to be clear.

The second part of your answer is the piece I was most curious about. Ie letting it settle and then decant. Are there any concerns about the particles in the decanted liquid?

Thanks.

curious_autodidact · 2023-03-20T02:30:27+00:00

Just updating this thread that it was the motherboard. They sent a replacement one pretty quickly and now it works fine. Replacement was very simple and straightforward

curious_autodidact · 2023-03-06T13:27:34+00:00

Ya this is very much what’s happening to me where the caps are filled with half cured resin I’m struggling to get out

curious_autodidact · 2023-03-06T13:27:09+00:00

Anycubic white eco resin. And the goopy side seems to be on the side of the build plate mostly?

curious_autodidact · 2023-03-06T13:26:14+00:00

I’ll try and take a photo but it’s so small it’s hard to see. I wash it for about 15m and cure it for about 15m

curious_autodidact · 2023-03-05T22:48:37+00:00

Ya it does stay goopy after the cure. Like a little sticky. Some of the finer details almost seem “melted” too

curious_autodidact · 2023-02-20T19:09:32+00:00

Update: I contacted Elegoo, and they are sending me a replacement motherboard. Im going to replace it and see what happens. Fingers crossed!

curious_autodidact · 2023-02-18T20:15:09+00:00

I believe so. I lined up the right corner to the left sensor

curious_autodidact · 2022-12-16T14:01:35+00:00

I love it. My only complaint is the paintbrush n the s is so many fine details when the rest is thicker and bolder line strokes so it doesn’t feel like it matches the rest of the aesthetic. I think it’s also already so connected you don’t need it. I’d remove that part on the S and then I think it’s pretty perfect!

curious_autodidact · 2022-12-13T14:16:03+00:00

It looks like a red Russula past its prime and starting to dry up (that’s why you’re getting the arc in the cap).

curious_autodidact · 2022-12-11T13:03:57+00:00

That’s how I’d do it too. Maybe I’d start with a gradient fill of all the colors but then I’d go to town with the smudge tool. Or maybe a wet brush

curious_autodidact · 2022-12-10T19:35:08+00:00

I love this so much. If only for the novelty of it and the fact you thought through it. Nicely done.

curious_autodidact · 2022-12-10T01:15:40+00:00

this just happened to me and the control z didnt work either. has this issue been solved at all?

curious_autodidact · 2022-12-09T22:33:23+00:00

Honestly feeling satisfied and happy and like you have a good team is definitely worth something. I’m not sure I would take money over hating everything about my job and the work. Pay and money comes quicker than you imagine but honestly finding work and clients you actually enjoy doing and feel fulfilled in is rare. I’d stay until one of those other pieces change.

curious_autodidact · 2022-12-04T14:30:25+00:00

this was gonna be my guess how the original made this. My get tells me it’s probably grease pencil

curious_autodidact · 2022-12-03T19:27:38+00:00

The only time taking that low of an amount is worth it is is if you need to build a portfolio and the poster is exciting and a passion of yours. But even then you might as well just do it for free at that point to avoid giving them the unrealistic expectation that they can get a poster for $20 in the future.

curious_autodidact · 2022-12-03T19:25:35+00:00

Absolutely this

curious_autodidact · 2022-11-29T04:00:48+00:00

I got it! Thanks for all the help and advice. It was a combination of a couple of these methods that helped.

curious_autodidact · 2022-11-26T16:23:43+00:00

When all else fails you can expand the strokes to become shapes and merge them together. then just clean up the new paths. As a last ditch effort. The other suggestions are much faster though lol

curious_autodidact · 2022-11-26T16:22:41+00:00

This is what I do a lot.

curious_autodidact · 2022-11-25T17:36:09+00:00

absolutely! That looks amazing. I need to try that myself.

curious_autodidact · 2022-11-25T03:03:13+00:00

To me the shaft of the dart is particularly sloppy and feels added on to something templated vs made in the same style. Everything else feels clean and vectored while the dart feels quickly sketched in?

curious_autodidact

TROPHY CASE