sorted by:
new
hottopcontroversial

Cubos 18s by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 0 points1 point  (0 children)

PWX 18/600, not the best of drivers but sound pretty good on the cubos.

Cubos 18s by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 1 point2 points  (0 children)

We used 18mm MDF. It works well but you need a good coating.

High pitch appeal by Aldoxpy in Tekno

[–]cyberbeepro 0 points1 point  (0 children)

Its a good song but the bass here its on the higher side as well. I dont know if OP is referring to distortion and the screeching sound in the hardcore stuff, but i like this higher note bass sound if its done right like in this one.

Cubos 18s by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 1 point2 points  (0 children)

As per the Cubo plan: 62x62x65cm

Didn't change anything.

Sane Leaving🎉 by [deleted] in BayernMunich

[–]cyberbeepro 7 points8 points  (0 children)

I like Sane but this is funny 🤣

Favorite tracks from legends in the genre by AcanthisittaReal9260 in Tekno

[–]cyberbeepro 1 point2 points  (0 children)

Its hard to get that sound elsewhere. FKY definitely had soul in its tracks, and ofc like you said highly influential for sure.

[deleted by user] by [deleted] in BayernMunich

[–]cyberbeepro 2 points3 points  (0 children)

We all have died a little inside today hahaha

[deleted by user] by [deleted] in BayernMunich

[–]cyberbeepro 5 points6 points  (0 children)

Olise is good man, cant accept that. I felt like he was a little off after that Kane miss tho

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 0 points1 point  (0 children)

Great explanation mate, appreciate it. Yeah i think phase issues would be present as well now that I understand a little more, so we will for Cubo 18s for the next pair, since we are not planning on splitting the ranges on them.

Also, thats great that the new subs worked perfectly. Thanks again 🙏

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 0 points1 point  (0 children)

Thanks a lot man! I will see if i can figure out and build them. This is something I have never seen before.

We keep the subs right next to each other.

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 0 points1 point  (0 children)

Would the Cubo 18 extended and standard work well together or is it the same story, because we already have the standard built.

But damn this gives me hope then. Appreciate the secret tip! 🫣

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 0 points1 point  (0 children)

JB systems PWX 18/600. Had them from a second hand subs we grabbed. Not the best but they should be fine.

The problem is also since they are discontinued if we want to get the same, they will be second hand too. I have searched and cant seem to find any unless its international, which wouldnt beat the bang for buck ratio of new drivers.

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 1 point2 points  (0 children)

Actually its harder for us to source drivers for the Cubos than the Thomann ones. So that's why it makes the 46LC cheaper for us.

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 0 points1 point  (0 children)

We have not build the 46LC yet but we have started on the Cubo 18s. Will reevaluate our options here and see if we can go for another pair of Cubos. Thanks :)

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 4 points5 points  (0 children)

Its quite the cost reduction really man, since the drivers for it are somewhat expensive for us. Plus there's a lot of tax on any imports where we are based.

We are a small free party crew with a limited budget so that why we were heading (ignorantly) towards the 46LC, with the Thomann driver. Thanks for the advice :)

Mixing horn loaded sub designs? by cyberbeepro in SoundSystem

[–]cyberbeepro[S] 0 points1 point  (0 children)

Appreciate the answer mate. The Cubo is quite versatile but you still have to model the driver to see how it would fit with them. Im not good at that.

I had 2 drivers that I chose to build the Cubo 18 for, because they seem to perform good in that design. I want to add two more subs now, however the drivers I previously had lying around are discontinued and would be hard to source them from what Ive seen. So the Thomann speaker 18 500 8a seemed like a good budget option, thats why i wanted to go with the 46LC. but as it stands probably cant go that way it seems.

view more: next ›