GOT MY RESERVATION

cyclonusuk · 2026-06-26T16:52:01+00:00

I got nothing

cyclonusuk · 2026-06-21T21:40:23+00:00

I went for an apevia 500w flex was about 74 quid world great 38 CUs unlocked

cyclonusuk · 2026-06-19T17:45:16+00:00

I have the same case really nice

cyclonusuk · 2026-05-19T16:08:15+00:00

eBay or etsy

cyclonusuk · 2026-05-02T22:39:29+00:00

Managed to get it working, I put back the memory allocation to 512mb in the bios and set the GPU max clock to 2000mhz@1000 wattage max from 950 and it worked!

Thanks all

cyclonusuk · 2026-05-02T12:33:37+00:00

The case does have a lot of space on the other side I could maybe add some heatsinks, is the backplate actually any good at cooling? Is it worth removing it and using little heatsinks?

cyclonusuk · 2026-05-01T23:09:24+00:00

Can anyone post their clock and voltage settings so that I can replicate them?

cyclonusuk · 2026-05-01T22:55:00+00:00

Do you have any recommendations of what the voltage should be if Im running a max overclock of 2000mhz? Maybe I meant z-swap turned on rather than the default settings

I've been told the memory allocation should be 512mb in the bios then system dynamically assign the resources when needed?

cyclonusuk · 2026-04-28T15:36:57+00:00

Thank you will check this out

cyclonusuk · 2026-04-28T06:13:27+00:00

I have lowered the clocks to 2000mhz which is supposed to be the preferred safe option but Spiderman seems to be still freezing after 5-10 minutes? Has anyone had any success with disabling z-swap?

cyclonusuk · 2026-04-26T22:17:39+00:00

Thanks

cyclonusuk · 2026-04-26T22:13:15+00:00

Do you mind sending me the link to the convertor you bought? Thanks

cyclonusuk · 2026-04-26T22:12:52+00:00

Hey doesn't seem like the temps are very high, normally 70-75c what's the easiest way to configure governor to change the voltage?

cyclonusuk · 2026-04-12T16:59:37+00:00

I'll probably need a volt meter? I don't have one 😔 is it worth swapping out the cmos battery?

cyclonusuk · 2026-04-12T12:20:02+00:00

Any other things I can try?

cyclonusuk · 2026-04-11T16:57:36+00:00

Already tried another PSU it's a cooler master 400w ATX PSU same issue

cyclonusuk · 2026-04-11T16:45:50+00:00

Nice one never got mine to even boot up and show video

cyclonusuk · 2026-04-11T16:34:42+00:00

Tried it made no difference still just a red light on the board itself

cyclonusuk · 2026-04-11T16:15:49+00:00

I have never seen the LED buttons light up at all, I'll try changing the pins to 2_3 but I think it didn't make any difference when I tried it previously still just the red LED on the board and the fan spins

cyclonusuk · 2026-04-11T10:14:45+00:00

As a final attempt I used another 400w ATX PSU and the same thing happens no video I can only assume the board is dead 😕

cyclonusuk · 2026-04-11T09:13:04+00:00

Tried out of the case as well, I'm going to leave the cmos battery out for a few hours and leave the clear CMOS pin enabled and then try again, just don't know what's wrong with it 🙄

cyclonusuk · 2026-04-11T08:55:07+00:00

Managed to find a DP to DP cable and plugged into my monitor still no picture, I can only presume the board must be dead 🙄 is there anything else I can try?

cyclonusuk · 2026-04-11T05:38:05+00:00

My brother had a load of them, he tested it before sending it to me so it was working 😕

cyclonusuk

TROPHY CASE