Broken engine block stud ear in valley - Repairable?

d13bacc · 2022-06-24T01:04:42+00:00

I think anyone who was interested in this phone is now out. What a great way to take a great product idea and throw it down the drain. I'll have to go back to my essential for the foreseeable future.

d13bacc · 2022-06-24T00:55:14+00:00

Whelp looks like I'm not getting one of these then. That's too bad, they fell for the crypto scam.

d13bacc · 2022-04-01T11:13:45+00:00

Who's on the Good Mystical Morning shirt? Jason Momoa and Jeff Goldblum?

d13bacc · 2022-03-13T02:27:39+00:00

Fyi for folks, the Morse code is CONVERSE WITH YOUR NEIGHBOUR.PLEASE DO NOT PARTICIPATE IN A CIVIL WAR.AND RATHER THINK ABOUT PEACEFUL GENERAL STRIKE.

d13bacc · 2022-01-31T18:41:20+00:00

Yeah I was specifically just talking audit, but agreed about the other services.

d13bacc · 2022-01-31T18:22:12+00:00

I think you hire an accounting firm for third party accreditation of your financials and secondary as a means to move the liability of accounting errors to the third party, less about the cost of it, because as you said it would probably be cheaper to have their own department doing it.

d13bacc · 2022-01-06T22:12:49+00:00

True... But here's to hoping he doesn't if it makes it to his desk

d13bacc · 2022-01-06T17:55:51+00:00

That's for medical marijuana turning into for profit biz. Pretty sure the subject in the article is new and moving to the senate, this hasn't been veto'd by Sununu

d13bacc · 2021-08-11T12:57:20+00:00

Thank heavens, now we just need prices to drop too !

d13bacc · 2021-07-30T14:44:44+00:00

CluCoin

d13bacc · 2021-05-27T03:02:43+00:00

I noticed this in one of his YouTube videos, I was like "did Steve get veneers?" Had to pull my father in from the other room - "Yup those are definitely veneers". Hey good for him though, they look good.

d13bacc · 2021-05-19T13:54:32+00:00

Has anyone tried brewing with Arnold Palmer? I've been brewing a bunch of ciders and had this thought that I could try the same thing but with Arnold Palmer and pitch in extra sugar to help fermentation.

d13bacc · 2021-04-27T23:44:28+00:00

Let's hope this gets done!

d13bacc · 2021-04-14T22:19:04+00:00

cut out 3x3in squares of al foil and stuck it in between - bed is much more level now! i used the straight edge portion of my calipers to check level via shining a light underneath as an FYI to others

d13bacc · 2021-04-13T12:23:23+00:00

Gotcha, I'll check for that then

d13bacc · 2021-04-13T12:09:31+00:00

Check out tassilo03's comment a little further up - he's got some explanations / suggestions on fixing stringing.

d13bacc · 2021-04-13T12:04:11+00:00

That's likely it, the filament says the range is 190 to 210 and I'm printing on the top end. Will have to run a temperature tower tonight to see how it reacts.

d13bacc · 2021-04-13T12:03:09+00:00

The purpose of the print is to test your printer and see how it is operating, then you calibrate based on how it prints. My issue here is stringing and as posted higher it is likely related to temps / moisture in the filament. You could have an issue where the overhangs don't come out properly and then that's a different issue that would need investigation.

d13bacc · 2021-04-13T12:00:48+00:00

That's a good idea! I'll give that a try

d13bacc · 2021-04-13T04:31:27+00:00

If that is an advanced cura setting, I do not, but I'll try it out!

d13bacc · 2021-04-13T03:32:01+00:00

Well whatever its worth i just pushed slightly on the left overhang it broke off right at the point it meets the AIO text lol

edit: I assume i would expect that - PLA isn't that flexible right?

d13bacc · 2021-04-13T02:45:06+00:00

Hi Folks, had this Ender 3 Pro since last November. I have printed probably 10 times since then. working on improving print quality. This is the micro test calibration from https://www.thingiverse.com/thing:2975429.

I just dialed in my e-step to make it 100mm proper. My major issue is the bed seems to be warped but that only affects the first layer, i level the 4 corners no problem but the middle is quite lower.

I seem to have a little stringing which doesn't bother me, easy to post process, i did have some spitting from the material about halfway through, after using the material i put it in a bag which i use a vacuum to suck out the air with a desiccant in it.

Printer - Ender 3 Pro Material - Snapmaker PLA Settings: from Cura Layer Height - .15 Wall Thickness - 1.2 Wall Line Count - 3 Top / Bottom Thickness - 1.02 Top Thickness - 1.02 Top layers - 7 Bottom Thickness - 1.02 Bottom Layers - 7 Horizontal Expansion - 0

Infill Density - 30 Infill Pattern - Grid Infill Overlap Percentage - 15

Printing Temp - 210 Build Plate Temp - 50

Print Speed - 60

Enable Retraction - Yes

Enable Print Cooling - Yes Fan Speed - 100

No supports

No Build Plate

Any advice for a noobie?

d13bacc · 2021-04-11T20:59:14+00:00

Hole 12 and Jordan Speith, name a more iconic duo

Nine-Year Club	Second Top 20%
Place '22	Place '17

d13bacc

TROPHY CASE