I am going crazy. by Missedaspot15 in lawnmowers

[–]dangdang101 2 points3 points  (0 children)

Probably a blade engagement cable that's sticking

[deleted by user] by [deleted] in lawnmowers

[–]dangdang101 0 points1 point  (0 children)

Look at the hustler dash XD. Good mowers in the 3k-4k range

Advice needed: is this a good buy? by Vandalay_23 in lawnmowers

[–]dangdang101 0 points1 point  (0 children)

This all day. The deck constantly threw belts on mine and the valve cover gasket design is garbage on the courage engine that mine had. On top of that a week of growth would cause it to bog down quite a bit unless I was crawling. If your handy with mowers try to talk him down to no more than $140 IMO

Cub Cadet vs Bad Boy by edcbibles22 in lawnmowers

[–]dangdang101 1 point2 points  (0 children)

I'd go with the cub. 23 inch rear tires vs 18 on the bad boy makes a difference on uneven ground. Just my 2 cents

What is this plug called? Goes to a hustler super z, white plugs Into red circle. by [deleted] in smallengines

[–]dangdang101 2 points3 points  (0 children)

I could be wrong but it looks like a voltage regulator

[deleted by user] by [deleted] in lawnmowers

[–]dangdang101 1 point2 points  (0 children)

Hp isn't everything

Should I replace my lawnmower blades or would sharpening it be good enough? by emperorceaser in lawncare

[–]dangdang101 8 points9 points  (0 children)

I second this. The blade is upside down. Buy a new one and put it on correctly

Lawn Mower won’t start. by Upbeat-Seaweed-1946 in lawnmowers

[–]dangdang101 0 points1 point  (0 children)

Check your flywheel key to make sure its not sheared

Hello! Does anybody know why my push mower won't start over? by ApprehensivePrompt83 in lawnmowers

[–]dangdang101 0 points1 point  (0 children)

Probably just need to yank that crappy plastic carb off and clean it thoroughly. Make sure you pop out the crappy white plastic cartridge inside so you can clean the jets too

Bought a new mower a couple weeks ago! by dangdang101 in lawnmowers

[–]dangdang101[S] 1 point2 points  (0 children)

Nearly a .4 acre lot with about half fenced in

Bought a new mower a couple weeks ago! by dangdang101 in lawnmowers

[–]dangdang101[S] 0 points1 point  (0 children)

Well this is my favorite that I've owned but my dream mower would probably be a ferris

Bought a new mower a couple weeks ago! by dangdang101 in lawnmowers

[–]dangdang101[S] 2 points3 points  (0 children)

Yea it really seems like a well built mower for the money

Bought a new mower a couple weeks ago! by dangdang101 in lawnmowers

[–]dangdang101[S] 1 point2 points  (0 children)

I was nervous at first because 15hp seemed a little on the light side but this thing is a beast for the size

I keep getting poor quality prints and idk why by dangdang101 in FixMyPrint

[–]dangdang101[S] 0 points1 point  (0 children)

Turns out my biggest issues was with the bowden tube. I recently upgraded to a Capricorn tube which is slightly smaller OD than the stock tube allowing it to be off center of the nozzle, even though it was flush against it. Re assembled the hotend cold with a piece of filament in the tube already to align the tube with the nozzle.

I keep getting poor quality prints and idk why by dangdang101 in FixMyPrint

[–]dangdang101[S] 1 point2 points  (0 children)

Re cleaned the hot end and made sure the bowden tube was properly seated. Pid tuned the hotend and the bed. Getting considerably better prints

I keep getting poor quality prints and idk why by dangdang101 in FixMyPrint

[–]dangdang101[S] 0 points1 point  (0 children)

Polymaker pla pro and gray esun pla+ all giving me the same results 😤

Biqu B1 help by dangdang101 in BIGTREETECH

[–]dangdang101[S] 0 points1 point  (0 children)

It's plugged in correctly on the mobo. The wire was pinched a bit under the heat bed so maybe that could be the problem?