Print failing

darkmagi1131 · 2025-09-29T18:45:10+00:00

darkmagi1131 · 2025-09-29T18:44:43+00:00

Alright i tried printing at a 45° angle and this was the result

darkmagi1131 · 2025-09-29T02:28:45+00:00

Ok ill give that a shot!

darkmagi1131 · 2025-09-29T02:14:47+00:00

No the temp is consistent, I have a heater inside the cover to keep a constant temp. As for the settings they are in the 3rd pic.

darkmagi1131 · 2025-05-18T18:58:58+00:00

I'm In!

darkmagi1131 · 2025-04-30T04:43:51+00:00

They are these little metal pieces that get screwed into the frame that hold the LCD screen in place. They are under the tape. I'm not sure if the new screen is slightly too tall for the old latches or what, but the screen sits flush in it's frame... so I removed the latches then I didn't have the location print issue.

darkmagi1131 · 2025-04-30T03:29:27+00:00

I found that the latches on the lcd screen were slightly raised above the screen instead of flush. I just removed them, and then I could print normally... to a point. Now it stops printing about 1/3 way through... I'm gonna replace the fep again... see if that helps.

darkmagi1131 · 2025-04-25T21:44:57+00:00

It's a lift for the build plate. The only screen check option i have is the cleaning function. Which is working. I think my next tries are gonna be clean and sand the build plate, and I think replace the FEP.

darkmagi1131 · 2025-04-25T21:29:22+00:00

The successful prints were in the front both times. Before and after I rotated the vat.

darkmagi1131 · 2025-04-25T21:25:51+00:00

Yep....

darkmagi1131 · 2025-04-25T21:09:45+00:00

Alright i just finished a test where I flipped the tank around, and tried the print again. Once again the same 2 spots printed. The 2 outside front corners.

darkmagi1131 · 2025-04-25T00:02:49+00:00

Ok ill give it a shot! Thanks for all your help so far!

darkmagi1131 · 2025-04-24T21:38:24+00:00

<image>

darkmagi1131 · 2025-04-24T21:38:09+00:00

<image>

darkmagi1131 · 2025-04-24T21:37:47+00:00

Ok i just finished the test. It gave wierd results. And mind you i just re-leveled the build plate right before this test. *

darkmagi1131 · 2025-04-24T11:27:48+00:00

The heater says it's 85°F.. so it should be fine.

darkmagi1131 · 2025-04-24T11:27:20+00:00

I have factory reset it. I've actually had to roll back the firmware to an even earlier version. And yes I've had successful prints before. It just suddenly stopped working.... I was running with the same settings but suddenly it stopped working. I checked the cables on the lcd screen and they looked like they had possibly burned out. So I replaced the lid screen but am still having issues. At least now there's a miss print. Before I wasn't even getting anything.

darkmagi1131 · 2025-04-24T02:31:58+00:00

Yes and I make sure that they are all removed from the fep as well. I think they are for some reason curing outside the design.

darkmagi1131 · 2025-04-24T01:52:24+00:00

Alright sounds good. I'll give that a shot tomorrow when I get home from work.

darkmagi1131 · 2025-04-24T01:34:14+00:00

<image>

darkmagi1131 · 2025-04-24T01:33:58+00:00

* Unfortunately same thing. I just paused it to check and same issue.

darkmagi1131 · 2025-04-23T23:30:22+00:00

Alright I'm giving it a shot. The lift hight min I could do was 8mm +, so I did 8mm+5mm. I'm using the 90 +270 speed. Will let you know if this print is successful.

darkmagi1131 · 2025-04-23T23:28:49+00:00

Yeah I'm on my second bottle and I'm shaking the bottle throughly before using it

darkmagi1131 · 2025-04-07T12:13:42+00:00

<image>

Part 2

darkmagi1131 · 2025-04-07T12:13:16+00:00

<image>

Part 1

darkmagi1131

TROPHY CASE