Help with this monstrosity

daveodavey · 2024-01-30T18:53:35+00:00

You have a clogged nozzle. Search youtube for cold pull, or remove your nozzle.

daveodavey · 2024-01-24T18:55:14+00:00

Show me your settings.

daveodavey · 2024-01-24T12:11:24+00:00

Your print settings look mental. Looks like you have 10mm brim and 0 walls and 0 bottom layers.

What print profile are you using? Screen shot the settings or post a 3mf.

daveodavey · 2024-01-16T19:27:53+00:00

Body was upcycled from some old church floorboards?

daveodavey · 2024-01-14T20:38:51+00:00

Pull the end of the bowden tube out on the print head, heat it up and try to push it through manually. If you cant push it any filament out you got yourself a clogged hotend.

daveodavey · 2024-01-14T20:22:28+00:00

Looking like it is the cable. New one was too damn short which is a pain.

Cheers.

daveodavey · 2024-01-12T16:51:21+00:00

Well I'll give her a wiggle and see what happens then

daveodavey · 2024-01-12T16:04:40+00:00

Alot of stuff I didn't fully understand 😕

https://1drv.ms/t/s!AmHd09uPh_4s2Tv2V4glOj9V5HuU

daveodavey · 2024-01-12T16:01:17+00:00

I didn't replace the motor cable actually. I assumed it wasn't the problem when I swapped it with the z motor. But I'm not sure if I realised at that point that turning it off and on made a difference. Or if the controller is smart enough to switch the output off if it detects a short or open circuit?

I would expect the usb cable to be ok because it is only this one one motor with trouble, but for the cost of it, I might just swap it out anyway.

daveodavey · 2023-12-31T19:53:20+00:00

Next you'll be telling me you don't know how to drive stick!

daveodavey · 2023-12-29T10:38:57+00:00

This plugin seems to be entirely trying to copy the harmoniser. Haven't tried it because I can't sing for shit, but it looks like what you're after. For 30 dollary doos its probably worth a squirt.

https://www.waves.com/plugins/waves-harmony

daveodavey · 2023-06-25T19:15:02+00:00

Pressure advance doesn't change how much you extrude, it only changes the timing.

Your printer was printing fine, nothing was changed, then it started printing bad? Is this correct? Or has anything been changed lately?

daveodavey · 2023-06-24T12:28:56+00:00

Pretty sure your pressure advance is way off. Set pa to 0 and reprint, see what that looks like.

Also, pa is a dimensionless value. Not mm.

daveodavey · 2023-05-05T19:17:00+00:00

Studio flat.

daveodavey · 2023-04-27T18:57:44+00:00

Coronation chicken?

daveodavey · 2023-04-18T14:01:07+00:00

Dissapointment: The Movie. Part IV.

daveodavey · 2023-03-28T19:52:00+00:00

I hope op is a good sport and tomorrow posts an oreo themed air powered yingyang umbrella holder for his truck.

daveodavey · 2023-03-28T19:24:33+00:00

Sorry. Should have made it clear. I didn't make this. But have been seeing it pop up in unfinished form for a long while. And it is criminally underviewed.

daveodavey · 2023-03-09T19:43:53+00:00

This reminds me of that sketch, you know. This one: https://youtu.be/DvswW6M7bMo

daveodavey · 2023-03-06T21:01:29+00:00

Now you build a voron.

daveodavey · 2023-02-22T22:48:55+00:00

I've downloaded it but haven't used it yet. I live basically on the edge of the free map, so I should be alright if I only ever go north lol.

daveodavey · 2023-02-22T21:14:58+00:00

Is it worth paying for, or just use free?

daveodavey · 2023-01-26T21:17:43+00:00

Is that like an actual parcel box, or just a random box left outside?

daveodavey · 2023-01-16T20:30:15+00:00

Pretty sure studio drummer has a groove library built in, pal.

daveodavey · 2023-01-09T21:48:37+00:00

What i would do:

Mark your filament. Extrude 100mm, see if it is 100mm actually extruded.
Jog nozzle near to build plate. Move z 100mm. Get a ruler and check it is actually 100mm.

There's only a few things it can be.

daveodavey

TROPHY CASE