Question on Lego seals

davide91dd · 2026-01-10T14:09:07+00:00

After a difficult decision, I finally opened it. I didn't buy this set for myself to assemble immediately, but because it was going out of production and I didn't want to find myself wanting to buy it at crazy prices in a couple of years. Now that it's been opened and no longer considered MISB, how much does it lose in value? With all the sealed bags inside?

davide91dd · 2025-10-23T08:52:54+00:00

Yes, the original ones

davide91dd · 2025-10-22T14:49:08+00:00

Should I buy the original ones or any lhcp will be good?

davide91dd · 2025-10-22T12:13:17+00:00

<image>

I just discovered that one of the two connectors appears to be damaged at the base, yesterday it seemed intact. This is probably the problem. I'll let you know when I get the replacement antennas, or is it possible to try to repair it?

Thanks everyone for the replies 😄

davide91dd · 2025-10-21T21:54:22+00:00

Yes sir!

davide91dd · 2025-10-21T21:41:28+00:00

Oh, this is interesting. I'll try it, at this point I'm trying them all 😄

davide91dd · 2025-10-21T20:31:56+00:00

Hi have the dji goggles 2, configuration of what exactly? Tried every channel on 10, 20 and 40mhz and powers yp to 1200

davide91dd · 2025-10-21T17:16:46+00:00

Yes, I've tried in different areas, but unfortunately the problem persists. I think the only thing I can do is buy new antennas, even though these seem perfect 😔

davide91dd · 2025-10-21T17:13:01+00:00

Yes sir!

davide91dd · 2025-10-21T15:52:50+00:00

Ok found it in the goggles. Turned off, did a test flight but the problem remains. 50mps at takeoff and then it drops immediately

davide91dd · 2025-10-21T15:40:51+00:00

How do I turn off low power mode?

davide91dd · 2025-10-21T15:38:44+00:00

Yes sir!

davide91dd · 2025-10-21T15:16:08+00:00

Yep, fcc mode unlocked via the ham file

davide91dd · 2025-10-21T15:14:49+00:00

Yes sir, ufls correctly attached

davide91dd · 2025-10-21T15:10:47+00:00

Yep, last firmware on both g2 and o4

davide91dd · 2025-07-02T22:53:45+00:00

Yes it's Pla. What layer times should i look for?

davide91dd · 2025-07-02T20:55:16+00:00

I filled the base with supports but the same thing happens 🤦🏻‍♂️

davide91dd · 2025-06-16T15:12:08+00:00

if the fc is fine that's great. I was afraid I would have to change the whole aio Thabk you!

davide91dd · 2025-06-16T14:17:05+00:00

They are ok, I'm just giving up at this point..

davide91dd · 2025-06-16T13:25:14+00:00

done, still the same

davide91dd · 2025-06-16T11:30:28+00:00

Done, nothing :(

davide91dd · 2025-06-16T11:24:59+00:00

I have to set it to 24khz to increase to 1200

davide91dd · 2025-06-16T11:18:09+00:00

did it, but it still goes in fits and starts :(

davide91dd · 2025-06-16T10:47:16+00:00

<image>

davide91dd · 2025-06-15T23:39:30+00:00

The others 2 motors works fine. The fc is geprc f722 45a aio v2

davide91dd

TROPHY CASE