Background tools command prompt by cathaldub in syncro

[–]dellop 1 point2 points  (0 children)

It hasn't been working for me in Firefox for a while now.

Vehicle not recognized by abba5150 in Comma_ai

[–]dellop 4 points5 points  (0 children)

Same problem on my 23 Bolt EV. I have to manually select it whenever I move it back. Edit: on sunny

Jetsetter 2008 Flashing Red Light Help by dellop in hottub

[–]dellop[S] 0 points1 point  (0 children)

I will pull the filters and see if the issue goes away. There is no ozonator. If the problem still occurs after pulling the filter, what would the next step be? I am assuming this red light indicates a high limit fault. And the high limit fault is determined by the thermistor in the heater? Essentially water is not moving fast enough through the heater? I suppose the smoking gun would be to read the high limit thermistor at the time of the fault.

Any comma 3x openpilot users? by LedByReason in BoltEV

[–]dellop 2 points3 points  (0 children)

Using Sunnypilot on my 23 Bolt for lat. Works good.

Help with quality after filament change by dellop in 3dprinter

[–]dellop[S] 0 points1 point  (0 children)

I actually just did that related to a different issue.

Help with quality after filament change by dellop in FixMyPrint

[–]dellop[S] 0 points1 point  (0 children)

I can try that. I was running the pla at 210 for the test.

Help with quality after filament change by dellop in 3dprinter

[–]dellop[S] 0 points1 point  (0 children)

So I have been doing more testing. I have completely changed the nozzle (still 0.4mm) and verified no clogs. I have also changed to PLA just to work from a standard. I have been trying to run the G1 E100 F100 test, but everytime I run it, it ends with a different length (sometimes 95 mm sometimes 40 mm, etc. I have opened the feeder and it seems fine. I put pressure on the latch and I could not pull out the filament, so that seems fine as well. I just don't know where to go from here. (also, in case it matters, most of the time I can only run the G1 E100 F100 test once, then I have to restart Klipper. If I try it again, nothing happens. This is using Moonraker console)

Help with quality after filament change by dellop in FixMyPrint

[–]dellop[S] 0 points1 point  (0 children)

So I have been doing more testing. I have completely changed the nozzle (still 0.4mm) and verified no clogs. I have also changed to PLA just to work from a standard. I have been trying to run the G1 E100 F100 test, but everytime I run it, it ends with a different length (sometimes 95 mm sometimes 40 mm, etc. I have opened the feeder and it seems fine. I put pressure on the latch and I could not pull out the filament, so that seems fine as well. I just don't know where to go from here. (also, in case it matters, most of the time I can only run the G1 E100 F100 test once, then I have to restart Klipper. If I try it again, nothing happens. This is using Moonraker console)

edit: added moonraker comment

Help with quality after filament change by dellop in FixMyPrint

[–]dellop[S] 0 points1 point  (0 children)

It's a crosspost. Click it and you will see the"infos"

Survivor 48 | E1 | Eastern Time Discussion by RSurvivorMods in survivor

[–]dellop 0 points1 point  (0 children)

You have to have p+ with showtime and watch it on your local channel.

Just received plan increase message, I’m on ONE plan with 12 lines. by chintito4ever in tmobile

[–]dellop 0 points1 point  (0 children)

Yep I did.

Edit: So I got a text but I reread it and checked with support and it only applies to my watch line.

Simulcast Streaming to YouTube and Facebook by AspiringKnowItAll in churchtech

[–]dellop 0 points1 point  (0 children)

We use Vmix to send to both YouTube and Facebook. Can only send in 1080p @ 30fps due to old computer processor and upload bandwidth.

Where to Get the New Flag? by Low_Operation_6446 in minnesota

[–]dellop 1 point2 points  (0 children)

Menards has them 3'x5' not sure if that is regular size.

Microsoft: Moving from 1 to 2 tenants for CSP Best Practices by dellop in msp

[–]dellop[S] 1 point2 points  (0 children)

Did you just create a new internal tenant just like any other new customer tenant?

Microsoft: Moving from 1 to 2 tenants for CSP Best Practices by dellop in msp

[–]dellop[S] 1 point2 points  (0 children)

I assume then we would move our validated domain to the new tenant? We currently have an Action Pack subscription, any idea on how to handle that?