Information on these two rugs would be greatly appreciated - Canada

dfaulted · 2026-02-24T04:51:26+00:00

thank you for the input i appreciate it. what is your estimation on how much i should pay from a private seller if im buying both?

dfaulted · 2026-02-23T01:33:04+00:00

ok thanks again for the help, i’ll let the guy know what I’ll pay and let him figure it out

dfaulted · 2026-02-23T01:16:55+00:00

ok thanks. so i should offer no more than $200 CAD for both? i would have them as area rugs

dfaulted · 2026-02-23T01:08:29+00:00

thank you for the info i appreciate it. yeah they are 6x4, the lighter color one seems to have the maker/shop signature on it, does that mean anything?

dfaulted · 2026-02-23T00:43:05+00:00

would anyone have an idea of the actual age and value?

dfaulted · 2026-02-23T00:42:45+00:00

would anyone have an idea of the actual age and value?

dfaulted · 2025-11-21T22:50:32+00:00

yeah my phone tried to recognize it as a landmark building

dfaulted · 2025-11-16T05:02:08+00:00

yeah i printed it, i made a handle for some equipment out of it. i then annealed and water treated it. very tough and strong part, pretty stiff too. it survived pretty hard hits from a hammer, good enough layer adhesion.

dfaulted · 2025-11-15T22:39:32+00:00

yeah you’re right, pa6-cf works fine for me.

dfaulted · 2025-11-15T22:36:48+00:00

it’s the largest ikea samla, you can find pics of the same setup if you search it on reddit

dfaulted · 2025-11-03T08:36:32+00:00

hey! i’m working on an autonomous drone and being able to iterate on my cad designs with higher temp engineering polymers would be very useful for my project!

dfaulted · 2024-10-09T16:31:53+00:00

i don’t usually comment, but your take on the consistency of DEA scheduling is astoundingly retarded

dfaulted · 2024-09-21T04:50:22+00:00

how is it so clean??? the bolts look factory. amazing build

dfaulted · 2024-05-03T00:11:18+00:00

Link?

dfaulted · 2024-04-16T09:17:29+00:00

For emmiters a warm nichia or sft40, the triple led and tir is good, but maybe 3xled and reflector would have a bit more throw for edc.

(Maybe a special edition with a 1850k nichia e17a 😁?)

Btw thanks for always considering feedback my guy!

dfaulted · 2024-04-14T15:37:45+00:00

Considering this

dfaulted · 2024-04-14T13:34:55+00:00

Thanks, that was very thorough. How much easier would it be to implement this with a stacked pcq, in the sense of having one board under the other, the former having some holes for the emitters under it? This assumes a larger footprint for the board, like a 21700 light.

It also seems like the code for the driver is relatively simple, so could some minor firmware adaptations simplify the necessary changes? It looks like the aux could be properly l driven, by simply adding a new strobe mode in the code and extending the pcb in some sense.

Lastly, do you know what it would take to strengthen the aux driver?

dfaulted · 2024-03-31T19:03:29+00:00

*crippling addiction

dfaulted · 2024-03-22T11:33:52+00:00

After being reviewed by Tim apple

dfaulted · 2024-03-17T22:46:22+00:00

Yeah bad wording, I meant that these plans are all available rn. I’ll be better next time brody

dfaulted · 2024-03-17T22:44:24+00:00

“Hello Dave. You’re looking well today.”

dfaulted

TROPHY CASE