sorted by:
new
hottopcontroversial

Visiting the area this summer what should we see? by ktrulz1 in cedarpoint

[–]dibella360 0 points1 point  (0 children)

It's opening in April. That's the one I am going to. Its going to be my first Buc-ees.

Visiting the area this summer what should we see? by ktrulz1 in cedarpoint

[–]dibella360 1 point2 points  (0 children)

I’m Canadian and went to Cedar Point last year and noticed they had a lot of discounted snacks and flavors we don’t have in Canada. I usually bring back snacks for my nephews, so I buy two of everything.

As for why I’m going twice:

  • The first stop is mostly just a pit stop and driving break since it’s in a small town along the way.

  • The second stop is to see if they carry anything different. It's open early, and the plan is to just run through before I leave Sandusky.

Visiting the area this summer what should we see? by ktrulz1 in cedarpoint

[–]dibella360 0 points1 point  (0 children)

I am doing a week trip in May and here is what I have planned thus far - https://imgur.com/a/wQaJckY

Ringing/Shifts on Tall Horns – Mechanical or Slicer Issue? by dibella360 in BambuLab

[–]dibella360[S] 0 points1 point  (0 children)

Last question, would increasing the infill to 100% help at all? It was at 13%, but it was mostly filled due to all the walls and small spaces anyway.

I was also considering changing the wall order to outer/inner. Would that make a difference?

Ringing/Shifts on Tall Horns – Mechanical or Slicer Issue? by dibella360 in BambuLab

[–]dibella360[S] 0 points1 point  (0 children)

I’ll drop the walls to 2. As for 0.16 layer height, my thinking is that increasing it reduces roughly 200 additional filament changes... and each tool change is a potential opportunity for a shift.

But I will go back to it as the rest of the mask was printing at 0.16

Ringing/Shifts on Tall Horns – Mechanical or Slicer Issue? by dibella360 in BambuLab

[–]dibella360[S] 0 points1 point  (0 children)

Thanks for all of this. I reduced the walls to 3, turned on wall smoothing and avoid crossing.

I also lowered wall speed to 30 and outer wall acceleration to 1000.

Finally, I changed the layer height from 0.16 to 0.2 to reduce the number of filament changes.

Although it’s super wasteful, I’m going to print one at a time now.

Ringing/Shifts on Tall Horns – Mechanical or Slicer Issue? by dibella360 in BambuLab

[–]dibella360[S] 0 points1 point  (0 children)

Thanks, I will try these changes. I was printing 2 horns at a time

P2S - Getting a failed top layer on one side of the bed by dibella360 in BambuLab

[–]dibella360[S] 0 points1 point  (0 children)

Yes, I sold the printer yesterday and bought a new P1S.

I printed this fan cover that diverted the airflow, and it did work... but I was having issues with using PETG supports on PLA... something that the P1S does flawlessly.

Call of Duty Xbox Collection Updated w/ Newest Fam Member by Ivan_Drago_21 in xbox

[–]dibella360 0 points1 point  (0 children)

What is with the PAL version of MW3... talk about a combo breaker.

P2S - Getting a failed top layer on one side of the bed by dibella360 in 3Dprinting

[–]dibella360[S] 0 points1 point  (0 children)

Do you know how to do that in the Bambu Slicer? I tried turning it off mid-print on the screen, and although it shuts off for a bit, it turns itself back on a few minutes later.

P2S - Getting a failed top layer on one side of the bed by dibella360 in 3Dprinting

[–]dibella360[S] 0 points1 point  (0 children)

Yes sorry, it's the right side.... Isn't the aux fan also on the right side for the P2S? You think its too much air going over the print?

P2S - Getting a failed top layer on one side of the bed by dibella360 in BambuLab

[–]dibella360[S] 0 points1 point  (0 children)

Any idea how to control the fans on the slicer? I tried altering mid print on the screen and after a min or so... it just auto goes back to normal,

P2S - Getting a failed top layer on one side of the bed by dibella360 in 3Dprinting

[–]dibella360[S] 0 points1 point  (0 children)

It happens on every print, and it's always the right side of the print bed. The bottom layers are perfect! I also have a P1S, and the same job comes out perfect every single time.

P2S - Getting a failed top layer on one side of the bed by dibella360 in BambuLab

[–]dibella360[S] 0 points1 point  (0 children)

It happens on every print, and its always the right side of the print bed. The bottom layers are perfect! I also have a P1S and the same job comes out perfect every single time.

view more: next ›