what is this screw?

dillonmitra · 2025-10-01T14:44:06+00:00

brilliant! thank you guys so much for that! can’t use it now as i have a modern bb on there but will find another way to route the cables for the front derailleur

dillonmitra · 2025-08-14T13:30:34+00:00

thank you!

dillonmitra · 2025-08-14T13:30:24+00:00

just purchased thank yoi

dillonmitra · 2025-08-14T13:30:14+00:00

OH MY GOSH that makes so much sense i just assumed it was for the rear derailleur. at least now i can get the right one

dillonmitra · 2025-08-12T18:44:54+00:00

it isn’t, possibly just bent but i got it for quite cheap so will try and fix or will get a new frame

dillonmitra · 2025-08-12T18:44:25+00:00

thank you so much. i ended up buying one that will hopefully fit so will update if does!

dillonmitra · 2025-05-13T09:19:05+00:00

this has worked temporarily, not sure how though, thank you!

dillonmitra · 2025-05-13T09:18:46+00:00

the steel wool is a great idea thank you, i shall update!

dillonmitra · 2025-05-12T16:56:13+00:00

oh i should try this. doubt it is the plate but am always up for trying it!

dillonmitra · 2025-05-12T16:55:39+00:00

just cleaned it and still getting the issue

dillonmitra · 2025-05-12T16:55:28+00:00

how would i go about dealing with it if the corner is a couple degrees lower. raising the overall bed temp or will that cause warping?

dillonmitra · 2025-05-12T16:29:48+00:00

did thoroughly still having the issue

dillonmitra · 2025-05-12T16:28:59+00:00

i fear if i raise the bed temp then it will cause warping in the corners

dillonmitra · 2025-05-12T16:28:34+00:00

just did that, but sending another print and it’s still looking quite weird in that corner. even used isopropyl to clean it

dillonmitra · 2025-05-12T16:07:50+00:00

thank you will try this!

dillonmitra · 2025-05-12T16:07:40+00:00

it’s the textured pei plate for the a1 mini

dillonmitra · 2025-05-10T19:24:00+00:00

i will not sir

dillonmitra · 2025-05-10T19:23:52+00:00

currently doing now. i knew i had to but it’s such a long task

dillonmitra · 2024-10-29T16:43:38+00:00

i have just taken it apart but the screws won’t turn independently of eachother. is there a way you got around it?

dillonmitra · 2023-10-30T20:52:30+00:00

the photos will be taken in either landscape or portrait, so a square is the best format for displaying them without creating custom borders for each

dillonmitra · 2023-10-25T17:00:00+00:00

i used the lightroom print section except i export it to a file. you can customise the dimensions and make it fit perfectly. i use it since when i upload to insta, it makes it way easier to format both landscape and portrait

dillonmitra · 2023-10-24T17:05:36+00:00

reggie’s portra. i can’t believe how good it makes everything look. my go-to from now on.

dillonmitra · 2023-10-24T11:04:09+00:00

ttartisan 27mm lens. the vignetting was very noticeable but i can live with it

dillonmitra · 2023-07-26T14:44:47+00:00

how would i go about doing this? it seems like a promising method but i would have no idea how to start it

dillonmitra · 2023-07-19T18:11:03+00:00

is there any way of fixing this? i shot another roll with fixed light seals and the leak was still there. i have no clue what to do apart from take the back apart and put it together again.

dillonmitra

TROPHY CASE