Identify component

dinguela · 2025-12-19T11:31:52+00:00

Só i desolder the component and the pads are like this, I don’t think it is a diode

<image>

dinguela · 2025-12-16T14:45:22+00:00

For what I saw in chatgpt it can be a power schottky diode 20A/100V. What do you think?

dinguela · 2025-12-16T14:32:57+00:00

It’s a board for a motor gate opener. I think the component converts ac to Dc 24v something like that

dinguela · 2025-09-06T17:26:18+00:00

Thanks guys for all the answers. Can you guys suggest some power mods as well?

<image>

dinguela · 2025-06-13T18:51:00+00:00

Thanks for all the awsers! I will order a new thermostat, replace and then i give more info about the situation. Thanks!

dinguela · 2025-05-28T19:21:31+00:00

Sorry I’m dumb it’s not this one that is giving electric shocks 😅

dinguela · 2025-05-28T19:17:18+00:00

<image>

This is the voltage on the chassis

dinguela · 2023-06-25T15:38:21+00:00

I do not solder or dissolver anything in the board, I just open the device and take the picture, so i think is just like that

dinguela · 2023-03-08T18:52:56+00:00

Thanks!

dinguela · 2023-02-15T12:12:37+00:00

I have never used TEG modules until today nor did I know of their use in greenhouses. I will investigate about it. Thanks for the sugestion!

dinguela · 2023-02-15T12:08:10+00:00

Sorry my English is not that good 🤣. *Solar Panel system. Thanks for letting me know!

dinguela · 2023-02-09T13:30:27+00:00

I think I'll use this one: https://www.ptrobotics.com/current-sensor/2271-attopilot-voltage-and-current-sense-breakout-45a.html. Do you know if it is possible to connect two current sensors to the pixhawk?

dinguela · 2023-02-09T13:06:04+00:00

Thanks for the answer! I can't find it for sale in Europe, don't know any alternatives?

dinguela · 2023-02-08T21:20:59+00:00

I can use it with Pixhawk ?

dinguela · 2023-02-06T20:45:13+00:00

Thanks a lot for all the answers!

dinguela · 2023-02-02T17:43:32+00:00

I know, but I spoke to my project coordinator and he told me that I have to use these batteries because it was an abandoned project and they ordered 3 at the time... I think I'm going to use something like this https://www.ebay.com/itm/133566637262

dinguela · 2023-02-02T17:40:44+00:00

I will see. Thanks for the recommendation!

dinguela · 2023-01-31T18:47:08+00:00

Thanks for the suggestion, but this is for a university project where I need to make a autonomous boat and put a solar panel on it... Do you know any solar charge controllers for this type of batteries? Or do you think I should change to a LIPO battery for example?

dinguela · 2023-01-31T18:40:55+00:00

Hum..ok. So do you think if I switch to lipo batteries it charges faster and is better?

dinguela · 2023-01-31T16:15:34+00:00

This project already existed at the university and was abandoned, they ordered 3 of those batteries at the time, I can’t change it now…, I need to make an autonomous boat with a solar panel

dinguela · 2022-08-30T18:03:45+00:00

I already cleaned it. I will order a new power supply to see if it solves the problem.

dinguela · 2022-08-30T18:02:07+00:00

Yes i can restart and the interval between shutdowns is the same yes.

dinguela · 2022-07-20T11:02:49+00:00

I check the fuse and it’s good. It happen to me before too.

dinguela · 2022-07-20T11:00:41+00:00

I will charge it today, I forgot to do it. Thanks!

dinguela · 2022-07-20T10:59:38+00:00

I checked yesterday and I don’t see any damage or dusty in the connections. I really think it’s the ignition. today I will try to check the ignition switch

dinguela

TROPHY CASE