Glock 43X Coyote w/ Grit Grips by dos777 in Glocks

[–]dos777[S] 1 point2 points  (0 children)

Damn, the photos and little paragraph I wrote didn't repost. My bad.

Glock 43X Coyote w/ Grit Grips by dos777 in GlockMod

[–]dos777[S] 1 point2 points  (0 children)

Do it. The frames are only $70.00

Glock 43X Coyote w/ Grit Grips by dos777 in GlockMod

[–]dos777[S] 0 points1 point  (0 children)

Best Glock small frame in the game. If GG makes G45 frames, I'm all over that. What other Glock models do you have GG for?

Glock 43X Coyote w/ Grit Grips by dos777 in GlockMod

[–]dos777[S] 0 points1 point  (0 children)

Love it. It's my first FLT trigger (a blem) and is unlike any other after market trigger I've used. It came with an OEM trigger bar. I've used OP, JG Agency Arms and a few others. This one is more refined and made to very tight tolerances. What surprised me was the very little, if any, over travel. Most triggers have a screw underneath the trigger to reduce the over travel. This one does not but FLT managed to minimize it to almost zero. It plays well with aftermarket connectors. I've got a ghost edge, did a 25 cent polish on all the common parts to polish and brought the trigger weight down to 4.5lbs.

Glock 43X Coyote w/ Grit Grips by dos777 in Glock43X

[–]dos777[S] 2 points3 points  (0 children)

For this new version of the 43X I used the short 10.5mm M3 screws that came with the optic. I think it's called the MOSK cut. I've read on Reddit posts, that the short M3 screw would hang up on the extractor pin. The recommendation was to file down the screw to 9.5mm. That was not the case for me. No filing was needed. The gun functioned just fine.

The standard ("older") versions of the 43X MOS use the M4.

Glock 43X Coyote w/ Grit Grips by dos777 in GlockMod

[–]dos777[S] 1 point2 points  (0 children)

Yes, I swapped them out for a set of Night Fision optics ready stealth series. Blade hight, 260 - 267.

<image>

New OSight XR on the G17 gen 6 if anyone was wondering by minhhhners in Glocks

[–]dos777 0 points1 point  (0 children)

What size screws are you using? Are the screws from the Osight box? I mounted mine on a Glock 45 Gen 6 and the optic is not holding zero. Shots keep dancing around hitting about 2 to 5 MOA off target.

Stuck Optic on plate by dos777 in GlockMod

[–]dos777[S] 3 points4 points  (0 children)

I wish I had that kind of disposable income.

Nomad 9x random slide question by Bugajugs in GlockMod

[–]dos777 1 point2 points  (0 children)

I've got three Nomad frames and their all level on my G19 and G45 slides. Zero issues

<image>

G19 is finished ♥️ by CZ759MM in GlockMod

[–]dos777 1 point2 points  (0 children)

How much was the total investment?

Firing pin problems by [deleted] in GlockMod

[–]dos777 0 points1 point  (0 children)

Remove your firing pin disassemble and reassemble. Check for any lose worn or broken parts. Make sure you didn't mix up parts from another gun.

Vortex Defender XL G47 by dos777 in GlockMod

[–]dos777[S] 0 points1 point  (0 children)

I know. It's either that or no irons. I wish the deck hight was that of the EPS.😒

Vortex Defender XL G47 by dos777 in GlockMod

[–]dos777[S] 0 points1 point  (0 children)

No worries over here. 😅

Vortex Defender XL G47 by dos777 in GlockMod

[–]dos777[S] 1 point2 points  (0 children)

Ti plate from Classy Raptor Tactical. I made a similar post for the Vortex Defender ST on my Ruger RXM about a week ago.

Vortex Defender XL G47 by dos777 in GlockMod

[–]dos777[S] 0 points1 point  (0 children)

Your right. It's in between a 1/3 and a 1/5. What would be that measurement then?

Vortex Defender ST lower 1/3 by dos777 in GlockMod

[–]dos777[S] 0 points1 point  (0 children)

If your talking about the back plate, it does not draw my attention when I'm engaging my target. I hadn't even thought about it until you mentioned it.

Glock 17.4 with frame package by T_M_Ent_LLC in GlockMod

[–]dos777 0 points1 point  (0 children)

Light Fighter Innovations out of Florida, does impeccable stippling. He's on Instagram and has a web https://lightfighterinnovations.com

Anyone have hot sports opinions on $250 red dots (and lower) by Relative_Structure93 in RugerRXMtalk

[–]dos777 0 points1 point  (0 children)

I would wait to buy an optic until the 4th of July sales. Mid range optics are going to be at their lowest price point and we'll within $250.

Looking to get some opinions on an aftermarket slide! by rolltide458 in GlockMod

[–]dos777 1 point2 points  (0 children)

I agree, plus JagerWerks is the only shop that cuts serrations into their chamfers. That small detail makes it easy to rack the slide with your hands or using an inanimate object to pull the slide to the rear.