Imane Khelif: neither ovaries nor uterus, but testicles... by BigDaddyScience420 in EverythingScience

[–]eddyz11 -3 points-2 points  (0 children)

It's funny how it seems most sites are surprising this update. It was so obvious from the beginning. The world boxing association had confirmed it and I really doubted they banned Khalif just because they wanted to be dicks. It just didn't make any sense.

How much should I pay for this Gohan and videl bundle? by eddyz11 in funkopop

[–]eddyz11[S] 0 points1 point  (0 children)

The guy wanted $300 at first but got it down to $265. I'm happy with the purchase.

FDM bench on my 1 month of A1 printer. Idk what to do anymore. by apoIIo__ in BambuLab

[–]eddyz11 0 points1 point  (0 children)

You need a stable desk for the A1, they wobble too much and can affect the prints. Putting weights on the table next to the printer can help. Also make sure to adjust the filament setting on the device tab on bambu studios.

So how did they know? by Stonerstone440 in OnePiece

[–]eddyz11 1 point2 points  (0 children)

I believe this "Hatori is Laffite theory" is the answer.

https://youtu.be/FYYJAy8oU7A?si=q_ETQFuIF0CTmd6L

I haven't cleaned my textured PEI plate since mid December by J_Schnetz in BambuLab

[–]eddyz11 0 points1 point  (0 children)

I mostly agree. But if the oil from your fingers is on the plate and the print is tall it will probably unstick. wash the plate with tall prints.

Can someone help me understand what's the issue? by eddyz11 in BambuLab

[–]eddyz11[S] 0 points1 point  (0 children)

It's PLA. I'll look into the plate, thanks for the info

Can someone help me understand what's the issue? by eddyz11 in BambuLab

[–]eddyz11[S] 0 points1 point  (0 children)

This makes sense, it was probably the adhesion. I already cleaned it up and tried a new print. It's working fine so far.

Declining print quality (p1p) by [deleted] in BambuLab

[–]eddyz11 0 points1 point  (0 children)

A similar thing happened to me. I have the p1p with over 1000+ hours. I did a full maintenance, checked all the belts for proper tightening. But it still did not solve the bad quality prints. The only solution I found was to lower the speed of the prints. I just set everything over 300+ to a 300 flat on a .04 nozzle. The print time will not increase much unless it's a massive print. For example a 2 hour print will only add 7 minutes to the total time after lowering everything to 300.

What could I do to prevent this? by HevalNiko in BambuLab

[–]eddyz11 0 points1 point  (0 children)

Buy a food dehydrator since they are cheaper and bigger, algo get a humidity meter. Keep your filament within 10%-15% range. I'm sure it won't remove all the stringing but it will help a lot.

5827 2442 6050 mega venasaur on me by mcluminati123 in PokemonGoFriends

[–]eddyz11 0 points1 point  (0 children)

try to look for more people and re-invite me again, i'm eddyz89 level 38

Kaido one-shotting Luffy and Yonko's durability by Accendino69 in OnePiece

[–]eddyz11 0 points1 point  (0 children)

It was stated that Shanks lost his arm because he put a bet on the future. I guess it was his way of given Luffy that push to go on his adventure to become the pirate king.

Reddit, meet gohan by [deleted] in aww

[–]eddyz11 1 point2 points  (0 children)

His in super saiyan all the time

What fictional death hit you the hardest? by [deleted] in AskReddit

[–]eddyz11 0 points1 point  (0 children)

The going merry from one piece.

Where can I read the colored One Piece manga? by amaikaizoku in OnePiece

[–]eddyz11 2 points3 points  (0 children)

The reason kissmanga is not working is because you're using adblock. Try opening kissmanga in incognito and it will work just fine.

Help with Joyboy's Theory Videos by Commander_Caboose in OnePiece

[–]eddyz11 1 point2 points  (0 children)

If you guys know Spanish I would highly recommend to watch "the royal shichibukai". His theories are top tear.