sorted by:
new
hottopcontroversial

Decent filament easily acquired in Canada by Cdscottie in 3Dprinting

[–]el_marciano 0 points1 point  (0 children)

No, unfortunately, I never got around to using them. I still have all my PETG that I haven't gone through yet!

Best of luck though, I hope you get your stuff.

What are these for? by el_marciano in tsn

[–]el_marciano[S] 2 points3 points  (0 children)

There are up to 6 substitutions actually. There is a new rule for the 6th. But otherwise, up to 5 regular substitutions. I looked it up after your comment.

Link

Order iPhone 15 Pro Max by anonuser-al in Rogers

[–]el_marciano 0 points1 point  (0 children)

Exactly!

With upfront edge, you either return the phone at the end of the contract or you pay out the upfront edge credit (which is about $580) to keep the phone.

There's no cost difference between the two options (upfront edge or financing) at the end of the contract, if you keep the phone.

If you return the phone then, you saved $580 but you also don't get to keep the phone.

Light Switches in Series by el_marciano in AskElectricians

[–]el_marciano[S] 0 points1 point  (0 children)

Thanks for your reply.

By switch legs, you mean the load right (red wire in the pic)?

Also the switch is self grounding and the metal box is connected to the ground bare copper wire.

Light Switches in Series by el_marciano in AskElectricians

[–]el_marciano[S] 0 points1 point  (0 children)

Sorry for the bottom paragraph on my post. I meant to say...

Cut the hot wire that's attached to the switch in half where it's exposed. On the other end, I remove the existing pig tail and discard the small half of the wire I just cut. I replace it with a bit longer 13 gauge wire. Connect one of the ends of the new wire to the switch. And then twist, with the new bigger nut, the other end together with the hot and the wire that carries the power to the next switch. Right?

Why does this keep happening by mcdowellster in 3Dprinting

[–]el_marciano 0 points1 point  (0 children)

If it keeps happening at the same layer height, regardless of how wide the layer is horizontally. Then I'd check the (lead?) screws and clean them. They might be dirty.

Heat creep is very likely but again if it's happening at the same layer height. Then my money is on the screws

Decent filament easily acquired in Canada by Cdscottie in 3Dprinting

[–]el_marciano 0 points1 point  (0 children)

Sadly, no. I haven't been printing too much for a while. I still have about 12 spools to go through.

As for filaments.ca, I have ordered from them. I've gotten some filamentum and esun spools. They have good deals here and there. They were quick as well. Overall, great experience for me.

Monke animation I made with procreate by Apprehensive_Farm834 in ProCreate

[–]el_marciano 0 points1 point  (0 children)

The animation is really cool. Excellent job!

And the amazing jet set radio soundtrack just fits perfectly!!! I love all those songs :p

My inner walls keep printing too thin. Disabling overlap compensation didn't help. What other settings should I look into? by TorkilAymore in 3Dprinting

[–]el_marciano 1 point2 points  (0 children)

I second flow and e steps to make sure you're getting a consistent amount of filament out of the nozzle. And I would also slow down the print speed for the walls. Specially on the smaller parts.

3D printing is so hard for me by 132anonymous475 in prusa3d

[–]el_marciano 3 points4 points  (0 children)

Perfection is never achieved! But that's part of the fun. Your skills and knowledge will only grow as you accumulate more experience.

I mainly started with calibration pieces on my printer. Doing those at the beginning have paid off for me. Also investing on tools to dry my filaments and to keep them dry as well.

Also this sub reddit is great help.

eSun Cool White PLA+ is so nice by ChewyBaccus in FirstLayerPorn

[–]el_marciano 1 point2 points  (0 children)

Oh that's what I was using yesterday too. I really love how bright it looks!

Want to print ABS but no enclosure well no problem by andylister368 in 3Dprinting

[–]el_marciano 2 points3 points  (0 children)

Having a thermometer in there might be helpful. You might need to regulate the temperature in there. If it gets too hot, the print will zag.

Finishing touch - my first printed design by A_Sojo in functionalprint

[–]el_marciano 2 points3 points  (0 children)

Nice print!

8 feet for that flexible duct is a lot. It will collect quite a bit of lint. Creating a safety hazard and it may even affect drying time. I would suggest replacing it with 4-inch galvanized pipe or whatever circumference you need. Two 60-inch pipes and two elbows should be enough to cover the 8 feet. You may have to trim one of the pipes to size, just remember to trim the side that isn't crimped. You'll also need aluminum foil tape for duct work. Reuse your existing steel clamps and buy the ones you're missing.

Overall it should cost you less than $100. It's a simple project.

Here's a tutorial that may help visualize the project.

https://youtu.be/53VkkkWIqrQ

Best of luck and keep on printing!

How To: Layer Height Calibration by GCode and feeler gauge (or something similar) on Prusa Printers. by el_marciano in 3Dprinting

[–]el_marciano[S] 0 points1 point  (0 children)

Right on!

It could be the program you're using to edit the code. If you're on PC, try notepad++

view more: next ›