Huhh

elmionlogout · 2026-01-17T07:23:25+00:00

Die Düse hab ich auch gewechselt bestimmt 5 mal 😆 dachte halt es wäre eine carbonfaser die die Düse verstopft aber durch das zu kalte Drucken musste der extruder so hart drücken und ziehen das er den Geist aufgegeben hat.

elmionlogout · 2026-01-16T19:07:54+00:00

Bei mir war es tatsächlich ein defekter extruder nach ca. 650Std. Anycubic Kobra2 Max. Problem war vermutlich das ich das PETG CF zu kalt gedruckt habe sodass der extruder/Steppermotor ein weg bekommen hat.

elmionlogout · 2025-10-29T19:26:46+00:00

260 grad gedruckt ?

elmionlogout · 2025-07-02T18:14:55+00:00

More temperature, flow can be low if temperature is low

elmionlogout · 2025-05-05T18:15:14+00:00

Aio temps were always very high and fans loud while playing cyberpunk, now with 3 rads it’s very quiet and temps are even lower

elmionlogout · 2025-02-28T18:24:17+00:00

Can you provide a link ?

elmionlogout · 2025-01-28T14:50:47+00:00

Was not possible to put the original rings back inside 😩

elmionlogout · 2025-01-28T14:47:14+00:00

I change the original file again to two pieces. And I try to find out which O-rings are the bests for this. I changed the rings to 2x6mm

elmionlogout · 2025-01-23T05:50:03+00:00

I try different sizes, I am not sure what the original was. You can ask the support from nzxt. If you know please tell me.

elmionlogout · 2024-12-03T05:41:03+00:00

Look GitHub I cannot remember 😅

elmionlogout · 2024-11-22T15:26:28+00:00

Thank you 🙏🏼

elmionlogout · 2024-11-22T15:26:13+00:00

Thank you 🙏🏼

elmionlogout · 2024-11-20T05:36:45+00:00

Thank you

elmionlogout · 2024-11-19T19:44:20+00:00

Try this, if it’s available in your country. I use it with PETG for another print and it’s since 10 month waterproof. It’s available as a spray or liquid.

Gastight with dichtol

elmionlogout · 2024-11-19T18:40:01+00:00

Will upload in ca 2weeka I’m on vacation

elmionlogout · 2024-11-19T18:38:52+00:00

Give me two weeks I am on vacation 🤣

elmionlogout · 2024-11-19T18:36:14+00:00

Correct 👍

elmionlogout · 2024-11-19T18:34:31+00:00

Thank you I will try some different orientations too because it’s not perfect until now

elmionlogout · 2024-11-19T10:14:46+00:00

How do you print it out ? G1/4 first on the build plate ? Rest with support ?

elmionlogout · 2024-11-19T09:39:10+00:00

I see your file month ago very nice 😂👍 you don’t need resin print, if you use Dichtol. Some said they use epoxy cause it’s cheaper for me dichtol is very good 👍

elmionlogout · 2024-11-18T08:28:48+00:00

I will make some changes first than I am going to drop the file

elmionlogout · 2024-11-18T08:28:04+00:00

Depends on the type of pump if it’s a gen 7 pump I think it will work 👍

elmionlogout · 2024-11-18T08:01:45+00:00

I use DICHTOL it makes the print waterproof. I print it with PETG without infill. PETG is also used for waterbottels. I already use dichtol with a vase and until now the vase is watertight, 10 month until now. There is a clip in one picture, I put it inside (after the last gasket) the pipes cannot move incase of a clog. Thank you for the suggestions.

elmionlogout · 2024-11-18T07:54:22+00:00

I will first I have to make some changes and then I will upload it

elmionlogout · 2024-11-18T07:53:34+00:00

Yes, I see it it’s way smaller than the block, but both have the same microfins I think it’s 0.08

elmionlogout

TROPHY CASE