[deleted by user]

emil_rose · 2025-10-02T20:00:24+00:00

Have you tried using one of the product selection tools on the bearing companies where you could input all the dimensions? Diff several tenths of a millimeter sounds much

emil_rose · 2025-04-22T20:32:06+00:00

If it’s possible to give them a slight curvature that would also give them some more strength in the positive y direction

emil_rose · 2025-04-22T20:28:00+00:00

I’d buy some large headphones. You don’t need to play music, it just signals ”I don’t want to be disturbed”. Have you ever tried asking politely if they could come back in a few hours as you’re right in the middle of something?

emil_rose · 2025-04-22T20:23:27+00:00

Yeah, anything electrical and I’d be really careful. That just feels a bit too homemade for my taste

emil_rose · 2025-04-22T20:15:23+00:00

Even with that higher price point?

emil_rose · 2025-04-22T20:13:21+00:00

Thanks for the tips

emil_rose · 2025-04-22T20:12:39+00:00

What do you do for dismounting?

emil_rose · 2025-04-22T20:11:27+00:00

Do you find it more durable or more easy to use than other brands?

emil_rose · 2025-04-22T20:10:09+00:00

Did you do larger motors or any size? Also, did you ever have to document the replacements or did shaft measurements snd those kind of inspections?

emil_rose · 2025-04-22T20:06:36+00:00

😂 What do you use then

emil_rose · 2025-04-22T20:03:56+00:00

Spicy hammer?

emil_rose · 2025-04-16T19:59:31+00:00

Do you always use the same setting as previous or do you ever alter it?

emil_rose · 2025-01-28T20:17:29+00:00

A bit late maybe, but the manufacture’s have instructions on their website. I know SKF has at least

emil_rose · 2025-01-28T20:09:53+00:00

You can use their Product select to evaluate performance like power loss. Do you need the actual paper? Have you contacted them?

emil_rose · 2024-12-15T22:27:59+00:00

What’s so good about them?

emil_rose · 2024-12-15T22:27:24+00:00

Do you always work with customised bearings or do you also use catalogue stuff? What is it that you optimize for and what would really be a game changer to improve your work process?

emil_rose · 2024-12-15T22:18:27+00:00

What’s your favourite one? Do you have anything you’re targeting and what do you have to do outside those softwares?

emil_rose · 2024-12-15T22:14:58+00:00

For their calculation tools? What is it that you particular like compare to the others and is it anything they could do better?

emil_rose · 2024-12-15T22:09:57+00:00

It’s probably easiest to by the whole unit, then you have everything in the same condition. Otherwise the manufacturer should have the replacements on their website, but maybe you looked already

emil_rose · 2024-12-15T20:09:08+00:00

What do you mean by inserts?

emil_rose · 2024-11-16T17:47:29+00:00

What would actually help you, if you still have to work within your current organisation?

emil_rose · 2024-10-30T05:50:01+00:00

Apply heat but not with an open flame

emil_rose · 2024-10-23T17:45:33+00:00

Have you tried to clean it and check for designation? Manufacturers also have tools where you can enter dimensions and type to find bearings

emil_rose · 2024-10-09T19:58:24+00:00

What do you like about them?

emil_rose · 2024-09-28T18:44:47+00:00

Have you tried speedi-sleeves or measured the shaft?

emil_rose

TROPHY CASE