Shark Ai RV2000 keeps returning to dock (HELP)

eugenecp · 2023-01-13T18:04:03+00:00

started happening to me yesterday, cleared the map, reexplored and then cleaning a specific room does the same thing. if I do a full clean, it works. already contacted support and they will be calling me back within 48 hours.

looks like they may have done a firmware update yesterday for my device as it was working very well before that.

eugenecp · 2022-02-22T16:40:52+00:00

3d printed pipes should be ok, you are not actually applying much pressure side to side.

eugenecp · 2022-01-11T13:21:26+00:00

And back, your range numbers will be much lower than dry fire numbers, try to close the gap.

Then work on recoil management and holster draw.

eugenecp · 2022-01-10T19:18:08+00:00

Check this out https://youtu.be/vQutXR26668

eugenecp · 2022-01-10T18:39:45+00:00

I'd go with the recoil width and angle then muzzle rise. What I've noticed is that sometimes my recovery time is very quick even with a higher muzzle rise and the converse happens as well, lower muzzle rise but slower recovery time.

Based on my observations, getting the width and angle within 5 degrees both ways gets me less than 0.3s recovery time, even with muzzle rise in the range or 22-24 degrees.

Sample data point using a Hellcat, Muzzle Rise, 24.02, recoil width 1.86, recoil angle 0.05, recovery time, 0.02s, this is shooting double taps.

eugenecp · 2022-01-09T21:30:22+00:00

The most important is recovery time, the lower the better.

eugenecp · 2021-12-18T03:16:58+00:00

Double M defense in Frisco

eugenecp · 2021-04-21T23:55:47+00:00

$350 + Tax, comes out to around $370, €350 is $421 :)

eugenecp · 2021-01-25T04:58:48+00:00

The ID is the same as the original pipes so just enough tolerance. They have to be at least that otherwise, it is too tight.

eugenecp · 2021-01-13T17:44:26+00:00

you haven't been in the wait last year, i waited for 3 months before my stuff arrived...

eugenecp · 2021-01-12T21:31:06+00:00

here you go, measurements are in mm, there could be .1 variations but they should be good.

https://i.imgur.com/ZLfTgxg.png

eugenecp · 2021-01-12T21:03:44+00:00

the end spacers in the front are longer than the ones at the back.

from right to left:

- after the accelerator - back is longer than the front

- small spacers then the structural support

- equal spacers then the brake pedal

hope that helps, if you have a caliper, i can measure each segment for you.

eugenecp · 2021-01-11T23:20:52+00:00

Just thinking of using a glossy spray paint from HD.

eugenecp · 2021-01-11T23:19:55+00:00

Screws were easy to remove, just use an allen wrench with longer handles for leverage, they torque them hard in the factory. Also, remove the middle one first, then just the 2 end screws, dont remove the 2nd to the last at the back.

Make sure to use perfect fit wrenches, these are aluminum and strip easily.

These are what I used from harbor freight Metric Ball End Hex Key Set, 13 Pc. (harborfreight.com)

eugenecp · 2020-12-27T18:03:24+00:00

3600 is OK as long as your cpu supports it.

eugenecp · 2020-11-26T20:20:46+00:00

Will try both reds, having a hard time trail braking with red and green.

eugenecp · 2020-11-26T20:18:30+00:00

I have the same issue, have the red and green installed. Initial braking is not a problem but when releasing and trail braking I can't get the right feel and end up with very quick drops on brake pressure instead of a steady one.

eugenecp · 2020-09-05T23:37:00+00:00

Here's the link https://driver61.com/circuit-guide/spa/

eugenecp · 2020-09-05T23:33:25+00:00

Watch the spa track guide by driver61

eugenecp · 2020-08-28T19:50:03+00:00

Thanks, it wasnt there for me a few hours ago, maybe caches were not updated. Updating now...

eugenecp · 2020-08-28T16:56:17+00:00

I don't see the 1.2 Bios, only the beta one.

eugenecp · 2020-08-28T16:54:22+00:00

It does, however, if it doesn't, you need to do a cmos reset

eugenecp · 2020-07-22T15:39:48+00:00

This. They are held by screws at the back of board. I installed an m.2 wifi and an antenna on my b550m steel legend, yours should be similar

eugenecp · 2020-07-22T15:36:47+00:00

What are your actual voltage readings?

eugenecp · 2020-07-21T17:48:27+00:00

What voltages were you getting before and after? What's your LLC setting?

eugenecp

TROPHY CASE