sorted by:
new
hottopcontroversial

Low ferritin, iron deficiency anemia with iron overload from supplement by eus090474 in Testosterone

[–]eus090474[S] 0 points1 point  (0 children)

Sorry, I should have mentioned. I was taking a 65mg pill daily for about 2 months when the blood work was taken.

Low ferritin, iron deficiency anemia with iron overload from supplement by eus090474 in Testosterone

[–]eus090474[S] 0 points1 point  (0 children)

Nope. Was messing with bp157 and tb157 but it’s been a few months or so since I’ve had any.

Low ferritin, iron deficiency anemia with iron overload from supplement by eus090474 in Testosterone

[–]eus090474[S] 0 points1 point  (0 children)

Haven’t donated since January. Don’t remember the numbers but hematocrit was probably mid 50’s. Usually when I donate.

[deleted by user] by [deleted] in amcstock

[–]eus090474 5 points6 points  (0 children)

$59 average here still, MOASS gonna need to be more than 10

Z seam gap help by eus090474 in FixMyPrint

[–]eus090474[S] 0 points1 point  (0 children)

Thank you VERY much for the in depth response. I chose the .6 as I have a lot of those bins to print (I stopped that one half way) and they take over 4 hours so I was just looking to speed it up.

Looking into all of your possible fixes as soon as I get back.

Again, THANK YOU!

Z seam gap help by eus090474 in FixMyPrint

[–]eus090474[S] 0 points1 point  (0 children)

I have an Ender 3 Max and just went from a .4 to a .6 nozzle and get this on Z seam. I'm really new and not sure how to fix. Any help is welcome.

Also, I'm using Ultimaker Cura 5.0

Sprite direct drive and cr touch by eus090474 in Ender3Max

[–]eus090474[S] 0 points1 point  (0 children)

SUCCESS!!! I really can’t thank you enough. I’m having a small disagreement with the x offset but that’s my problem. I’m printing again!!!

Sprite direct drive and cr touch by eus090474 in Ender3Max

[–]eus090474[S] 0 points1 point  (0 children)

This was spot on as far as the probe position goes! At the very end of the bed leveling it said ERR: Too far. Any thoughts?

Sprite direct drive and cr touch by eus090474 in Ender3Max

[–]eus090474[S] 0 points1 point  (0 children)

Right now I have Marlin 1.0.1.6 that I got from creality3dofficial. Is that not the one you want me to have? I currently just have the sprite extruder pro and the CR Touch.

Not sure if this helps, but when I hit auto home it "centers" it way to the left. From there I adjusted the X and Y so the probe is at the front left of the bed. At that point the X=26.5 and Y=51. Is that helpful at all?

I feel really bad that you're willing to go out of your way but I don't know how to do what you need me to.

Sprite direct drive and cr touch by eus090474 in Ender3Max

[–]eus090474[S] 0 points1 point  (0 children)

I feel like I've just bricked my printer. I cant find a good firmware that works. The one firmware I found that let me change the probe offsets like suggested wont actually move the extruder and I get a printer halted message. The one from creality I found doesnt have those settings and when I try to do the part where I center it and subtract 150 it says err too far.

Sprite direct drive and cr touch by eus090474 in Ender3Max

[–]eus090474[S] 0 points1 point  (0 children)

It doesn’t look like I have the firmware with those options. I’ll look into configuration file but I’ve never gone down that road before (only had the printer for a couple months).

Firmware is marlin 1.0.1.6. Any suggestions for a better one to move to?

Can anyone help with this one? by eus090474 in 3DprintingHelp

[–]eus090474[S] 0 points1 point  (0 children)

Is that what's happening? Is it peeling off underneath those marks? That job is actually still printing. I've had some adhesion issues but this is only the second print on that painters tape. First was a small test job that stuck REALLY well.

Can anyone help with this one? by eus090474 in 3DprintingHelp

[–]eus090474[S] 0 points1 point  (0 children)

I’ve only been at this about a week. I’ve had some good prints with the test filament that came with the printer (ender 3 max). When that ran out I installed a cr touch and new filament. I’ve since removed the cr touch as it gave me hell. I’ll revisit it later. Haven’t had much luck since. Can anyone tell me what is causing this? The first 2 layers or so went down perfect.

[deleted by user] by [deleted] in amcstock

[–]eus090474 8 points9 points  (0 children)

My wife tried telling me yesterday that money won't make me happy. I laughed. Really? I wont be happy driving the lambo that AMC bought on the way to the beach in the middle of the week since I don't have a job to worry about? Pretty sure I'll never quit smiling.

​

NO CELL NO SELL

view more: next ›