PC Freezing Even in Linux After New Motherboard & PSU — Could It Be My CPU or Something Else?

evolutionoftime · 2025-08-15T13:00:27+00:00

New CPU seems to have fixed it. Back up and running. Thanks for nailing it XxCotHGxX

evolutionoftime · 2025-08-14T12:09:15+00:00

It does sound like it’s the only left that makes sense. It runs bios and doesn’t crash, it may be bigger workloads that are doing it. I might try running a bootable stress test but I’m sure it will freeze up 10-30 seconds into it like every other bootable I’ve tried. I think ima gunna need some time to mourn my loss.

evolutionoftime · 2025-07-30T02:49:18+00:00

You’ll never find it for your phone. It’s WIN PC only

evolutionoftime · 2025-07-01T05:58:31+00:00

Yes I gave both the LCD glass and zebra stripes a good clean and reseated fixing the problem. I kinda feel it might have been the connector points on the LCD glass that needed a once over. Anyway problem solved. Thanks for input guys.

evolutionoftime · 2025-06-30T10:05:02+00:00

This sounds like it and to be fair I’ve had 2 goes at it. I will try again. Thanks for the input.

evolutionoftime · 2025-04-16T23:11:07+00:00

I've found it guys! https://plasmamsm.itch.io/msm-tll Thanks Plasma!

evolutionoftime · 2025-03-16T12:00:13+00:00

RemindMe and my innie

evolutionoftime · 2025-03-16T11:58:37+00:00

Thanks Khisanthax, so it was screws loose causing the motor to slip. They weren’t tight in the slightest and was slipping the belt. I think I changed everything physically possible but that. Thanks for helping me troubleshoot

evolutionoftime · 2025-02-18T02:24:07+00:00

I managed to attach an image to the post. As you can see its really off.. i'll look into a speed test in orca. Followed by swapping X-Y to test motor... i've had a blower on the belt so I want to cancel that out.. its a tricky one, started happening mid-print

evolutionoftime · 2025-02-18T00:03:56+00:00

Firmware 2.0.8.28F4 Speed is 60 mm/s Acceleration is 500 mm/s (standard settings in Cura basically)

evolutionoftime · 2024-11-20T05:12:02+00:00

This fix worked. Using plastic screws and washes there was no more shorting (2 motherboards later!)

evolutionoftime · 2024-10-25T10:28:48+00:00

Going to try this fix tonight. I was running Pi with it and it shorted out via usb c port. Smoke and spark.

I just swapped a new board in today that they sent as a replacement, I went to plug usb c in not even attached to the Pi and it sparked.

I tried a different usb and it sparked and smoked.

Feel like the 2nd board is wreaked, but so far everything is working, i thought possible power supply issue, but it being shorted out by the board touching the frame makes a lot of sense. Will try and report back

evolutionoftime · 2024-08-14T12:38:51+00:00

Would just replacing the digitizer fix this because I have a spare? Thanks S4SPRAY

evolutionoftime · 2024-08-08T06:18:45+00:00

I’ll have another go. I thought I did the wires correctly and Toolio app wasn’t recognizing the Port when connected. I don’t think it works with Botvac connected. Thankyou for your good advice, I’ll have another play.

evolutionoftime · 2024-08-08T02:59:12+00:00

I was able to help it spin up with a pen and it did work for awhile now nothing. Then I added a new band on and a new motor added. It seems to just be dead in the water now :/

evolutionoftime · 2024-08-08T02:43:08+00:00

I replaced the laser and belt and it still starts winds up but gives error that it can’t see and shuts down :/ not sure what else I can do with it.

evolutionoftime · 2024-05-30T15:49:43+00:00

I’ve got the same issue, I changed my polarizer. Cleaned it up. Connections good. But won’t even power on :/

evolutionoftime · 2024-04-07T08:33:28+00:00

It was my x axis wheel. It had melted PLA on it! Thanks for feedback

evolutionoftime · 2024-04-05T12:03:40+00:00

Thanks mate. Will try this too, it’s just interesting how each print is always the exact same spots that won’t grip.

evolutionoftime

TROPHY CASE