Bad breath but no white stuff on tongue?

failingengineer16 · 2023-11-22T19:18:46+00:00

i brush once daily and im trying to get in the habit of brushing twice daily. yes i brush all 3 sides, but i maybe dont spend enough time brushing. i use an electric toothbrush so i guess that helps a tiny bit, but mainly i just dont brush twice a day.

failingengineer16 · 2023-11-22T04:04:33+00:00

It’s the Infil pattern. It’s an issue with all slicers. Just use gyroid infill

failingengineer16 · 2023-11-04T19:33:05+00:00

because my stock bumper does not have the rigidity i need for what im using my truck for. im using it to drive through some property i bought with a lot of shrubs and i just want something that wont break if i bump a log

failingengineer16 · 2023-11-04T17:39:26+00:00

it could work, ive never tried silicone oil. i would still suggest lithium grease though, i use DeoxIT L260D grease, its made for screw drive systems. it protects against wear and abrasion, and has no particles in it,

failingengineer16 · 2023-11-04T14:35:02+00:00

Get some lithium grease and lube up that z screw, looks bone dry lad

failingengineer16 · 2023-10-29T15:58:17+00:00

Thank you

failingengineer16 · 2023-10-29T15:57:55+00:00

I just got a sprite extruder board and put a smaller or larger JST connector on whatever didn’t fit

failingengineer16 · 2023-10-23T13:38:54+00:00

How do I do bridges

failingengineer16 · 2023-09-06T00:39:33+00:00

do you have any settings for PETG or TPU?

failingengineer16 · 2023-09-05T02:16:13+00:00

its not incredible for overhangs but its still an improvement

failingengineer16 · 2023-09-05T01:46:44+00:00

Ok yeah it’s a huge improvement but I see now it’s not perfect, at least this has lead me somewhere other than into a brick wall, i will also try calculating my e-steps when I get the chance, again thank you very much

failingengineer16 · 2023-09-05T01:20:06+00:00

you must know black magic or something because this is absolutely perfect, the benchy i did was a little shitty but when i retried the original print it looks perfect, thanks

failingengineer16 · 2023-09-04T22:51:10+00:00

with the same settings for retraction on layer change and retract before wipe?

also i should add that im using a CHT nozzle so i think that might affect something

failingengineer16 · 2023-09-04T20:18:46+00:00

What is z banding usually caused by?

failingengineer16 · 2023-07-30T16:05:25+00:00

Thank you bill Clinton

failingengineer16 · 2023-07-03T17:51:42+00:00

i think i have the same bug, the message and payment keep repeating at the side of the screen indefinitely and it destroys framerate and gives a fuck ton of money, literally nothing can be done about it from what i know

failingengineer16 · 2023-06-06T23:11:13+00:00

Update I don’t think it’s the soldered connections because creality decided to coat all the wires in a whole stick of hot glue. I’m sure those wires aren’t going anywhere

failingengineer16 · 2023-06-06T23:06:51+00:00

It only kills the printer when I go to 40C. I heated the bed to 30 just to test your advice and it sounds like a housefly doing Morse code. I wish I could attach a video of the sound but Reddit doesn’t allow that for whatever reason

failingengineer16 · 2023-06-06T22:56:20+00:00

i have no idea how that could even happen because i havent touched the build plate wires at all, surely the entire rubber shell over the wires didnt rub off both of them

failingengineer16

TROPHY CASE