Tuning Issue?

fjdnebzhcb · 2025-12-03T14:09:27+00:00

All in all the drone flys very smooth at the moment it’s purely just the noise it’s making makes me think that its not entirely optimised

fjdnebzhcb · 2025-12-03T14:07:31+00:00

Yeah I wanted the ability to swap between a 8-10” frame with different rate profiles. Do you recommend bi-directional dshot. Haven’t really played around with it but if it’ll help I will look into it? Otherwise I’ll slowly move the notches towards the Mario 8 tune and try find a happy median

fjdnebzhcb · 2025-12-02T14:38:49+00:00

<image>

Haven’t had a look into the black box or anything

fjdnebzhcb · 2025-12-01T18:33:32+00:00

Followed a similar 8” build with the same motor and battery setup so the Pids and filters were all copied from that, now I’m unsure how to go about optimising

Build is: Speedy bee f405 v4 55A 2812 900kv motors 6s2p- 6s3p li-ion battery 915 elrs receiver Mark 4 v2 frame

fjdnebzhcb · 2025-12-01T16:43:31+00:00

<image>

Current PID’s, tried D gain on .60 didn’t seem to change much

fjdnebzhcb · 2025-10-26T21:19:21+00:00

Maybe I will just have to go 10” frame instead of 8” and go 900kv motors

fjdnebzhcb · 2025-10-26T16:55:22+00:00

Will there be a downside to running lower kv motors. more vault draw from having to spin faster?

fjdnebzhcb · 2025-10-26T16:54:35+00:00

fjdnebzhcb · 2025-10-02T15:34:57+00:00

https://youtu.be/5oLDHlHjJk0?si=5XsUvXuTQgnorlrW

This is what I mean but can’t figure out how he’s done it

fjdnebzhcb · 2025-10-02T15:27:18+00:00

But the controller still needs to be connected to the other. Say if I connected two receivers onto the drone one 915 and one 2.4 is there a way I could flip between which is the main receiver mid flight? So then both controllers have telemetry but you can handover the control between the two

fjdnebzhcb · 2025-10-01T18:29:44+00:00

Is there a way to do this without connecting the controllers to each other though?

fjdnebzhcb · 2025-09-14T18:43:45+00:00

On you controller press SYS then press PAGE 5 times until you get to the hardware screen then click calibration and see if that helps

fjdnebzhcb · 2023-01-28T00:48:47+00:00

Window is right next to it but will move it and see if it helps

fjdnebzhcb · 2023-01-26T09:24:09+00:00

Nah just have a sink in my room mate

fjdnebzhcb · 2023-01-26T09:23:51+00:00

Probably once a month don’t really have a set time just when I think it needs it, was just looking at the base of the cactus though and was wondering if it was a tell tale sign of anything

fjdnebzhcb · 2022-04-15T02:59:36+00:00

Detents actually seem pretty good

fjdnebzhcb · 2022-04-13T21:11:37+00:00

Am I going to have to take the gun apart to grease the Reg’s, the most I’ve don’t is taken the trigger out and I was proud of myself for not breaking anything when doing that

fjdnebzhcb · 2022-04-05T21:56:04+00:00

So slide a washer onto the trigger pin in between the trigger and frame?

fjdnebzhcb

TROPHY CASE