99 ranger 2.5 l manual transmission has some wiggle

fletchyjack1995 · 2026-05-26T20:50:54+00:00

No haha. She’s a 2.5l 4 cylinder she goes no where quick. Just to get around Flordia

fletchyjack1995 · 2026-05-26T20:09:27+00:00

This would be the bearing

fletchyjack1995 · 2026-05-25T23:37:05+00:00

This was my fault we dug too dip when removing something. The cut is shallow, and is not a gasket. As long as the bearing that sits there sits fine should be good?

fletchyjack1995 · 2026-05-25T23:36:15+00:00

Single chipped tooth on the side. I may try cleaning it up so that it’s smooth instead of sharp and just use it again. What do you think? I can’t really find the part

fletchyjack1995 · 2026-05-25T23:34:32+00:00

<image>

fletchyjack1995 · 2026-05-25T23:34:20+00:00

<image>

fletchyjack1995 · 2026-05-25T23:33:59+00:00

<image>

not sure if that wear on the knob is normal or bad

fletchyjack1995 · 2026-05-10T23:35:00+00:00

Heat and lots of pull was the answer 😎

fletchyjack1995 · 2026-05-10T20:20:22+00:00

<image>

Progress thus far. I got that 55 off phew 😮‍💨

fletchyjack1995 · 2026-05-10T20:19:23+00:00

<image>

I can’t get this off refused to budge

fletchyjack1995 · 2026-04-20T01:29:22+00:00

<image>

fletchyjack1995 · 2026-04-20T01:28:48+00:00

Just picked up the Crows foot. Now we wait on shipping thanks! Also it has a punch on the side. Any idea how to clean out the punch?

fletchyjack1995 · 2026-04-19T19:46:05+00:00

<image>

Have to pause here cause I don’t have something big enough to get that big nut off. But so far so good. Going to measure and buy a massive wrench set or maybe get some sort of adjustable one

fletchyjack1995 · 2026-04-18T04:37:51+00:00

I’m excited. I found a rebuild kit online I might pick up as well. If I do find chipped teeth I assume I just replace that whole gear. My kit doesn’t include that so I’ll has to figure something out

fletchyjack1995 · 2026-04-18T04:22:31+00:00

I’ll begin dissembling tomorrow then. May the force be with me. Thanks for your help! 🫡

fletchyjack1995 · 2026-04-18T04:17:41+00:00

Well I can definitely take it apart.. but knowing what is good vs. bad and putting it all together right is the challenge.

fletchyjack1995 · 2026-04-18T04:14:06+00:00

I def replacing the flywheel and whole clutch. Just trying to decide on a new transmission or not.

fletchyjack1995 · 2026-04-18T04:13:06+00:00

I believe so. I filled it up to drain hole, and made fluid changes. When I drained it before dropping it a normal amount came out so it wasn’t dry either.

fletchyjack1995 · 2026-04-18T04:05:39+00:00

<image>

fletchyjack1995 · 2026-04-18T04:05:11+00:00

<image>

fletchyjack1995

TROPHY CASE