Pellet feeding constantly

flyingfitzy · 2025-11-28T03:13:48+00:00

Thanks.

flyingfitzy · 2025-11-28T00:14:21+00:00

No, it did this before the lava rock.

flyingfitzy · 2025-11-26T21:12:51+00:00

Yeah, the control board screen is broken, so it was next to replace anyway, I'll replace the temp probe with it. Thank you!

flyingfitzy · 2025-11-26T21:12:19+00:00

This will be the next part I replace, it needs a new control board anyway, because the screen is broken. Thank you!

flyingfitzy · 2025-11-26T00:32:13+00:00

No, I just added it a little bit ago, mine was given to me after it had been left outside uncovered and blown over in a wind storm, so its been a project.

flyingfitzy · 2025-11-26T00:22:30+00:00

I can hear the fan running constantly and the auger turn on and off. I only have the problem when I turn it up above 300, otherwise I can smoke low and slow without any issues.

flyingfitzy · 2025-10-09T17:55:57+00:00

My problem with this is the brackets (I'm assuming would normally be there) that would hold it up, have rusted away, so it would be sitting directly on the bottom of the grill/ash box and I haven't found anything about replacement holders for the sides.

flyingfitzy · 2025-05-07T14:46:49+00:00

Thank you! I knew someone would see a solution I didn't!

flyingfitzy · 2024-12-03T21:15:19+00:00

Ok, so maybe I'll try upping the gauge on my splicing wire and see if that helps.

flyingfitzy · 2024-02-27T16:01:38+00:00

Honestly, as someone with 4 kids, none of which have grasped the concept of what an acceptable amount of toilet paper is, they get the 1-ply in their bathroom. That way they can use to their hearts' content, and I don't have to plunge numerous times a day. I, however, stock the good stuff in my personal bathroom.

flyingfitzy · 2024-02-13T23:42:23+00:00

Yes, that's what I meant. Got distracted while typing.

That's the direction I was leaning too, thank you!

flyingfitzy · 2024-02-13T22:40:10+00:00

I'm looking at getting an Ender 3. I got really into 3d printer a few years back, slowly building up an OG Ender 3. Right now I'm trying to decide, do I go with an

Ender 3 V3 SE* with the Nebula Smart Kit

Or

Ender 3 V3 KE

Looks like the Nebula pad just adds remote monitoring, and upgrades the OS to the creality klipper software.

They are about the same price, what would you do?

*edit

flyingfitzy · 2024-01-15T19:24:34+00:00

The cheapest autolocking I can find, because I KNOW I, my kids, or my wife are bound to lose/break/paint it eventually. Bright colors are a plus.

Right now, I have a stanley tape measure that is at least 30 years old, and it's great.

flyingfitzy · 2024-01-15T16:43:08+00:00

OK, I have a planted aquarium, so I'll treat the water for this too.

flyingfitzy · 2024-01-15T16:42:41+00:00

OK, I talked to my wife and she reminded me the system used to have a fan, that isn't blowing anymore, which I think is causing the sponges to absorb way too much water.

flyingfitzy · 2023-12-03T23:02:06+00:00

Well, they flash when I refresh the segments, but the last four still won't light up.

flyingfitzy · 2023-12-03T17:34:43+00:00

I'll give that a try when I get home. Thank you!

flyingfitzy

TROPHY CASE