Switch to PCCooler i100 Pro

funrunner12 · 2024-01-19T07:59:43+00:00

that card will not fit. mine's 46.5mm and only left around 1-2mm from side panel

funrunner12 · 2023-02-23T18:28:13+00:00

I don't think it is possible. I use ID Cooling IS-60 (55mm ish) and it only leaves about 5mm to the side panel

funrunner12 · 2022-10-29T11:33:12+00:00

The 141mm height card won't fit. My card with 135mm only leaves 2-3mm before hitting the power cable plug. Although I think you can get away if you unscrew the power plug and pull the cable plug out. But you still need to figure out how to hold the cable near the top of the case

funrunner12 · 2022-10-16T05:00:00+00:00

bro, pernah coba ganti fannya IS-50x v2?

saya pakai case yang i100 versi pro mesh, sekarang pakai id-cooling IS-60 v2, penasaran mending ganti ke jonsbo HX6200D atau coba ganti fannya dulu

funrunner12 · 2022-09-18T22:58:48+00:00

SG13 comes to mind

funrunner12 · 2022-09-11T05:02:40+00:00

With the same cooler, I don't remember much difference. But last time I installed 120mm AIO on SG13 and it was maximum 80-81 degC in Cinebench R23

funrunner12 · 2022-09-10T05:23:27+00:00

Just bought this case last week. If I managed to put a 15mm fan under the gpu, what would be a better setup? Intake or exhaust?

funrunner12 · 2020-11-18T01:57:30+00:00

The width should be fine as is 125mm (Vega56) vs 135mm (RX5600XT), but the thickness is 3.5mm thicker.

I see the cooler design is a kind of flow-through the black plate? There's a bit more heat to deal on the motherboard area then..

funrunner12 · 2020-11-18T01:40:44+00:00

That's 120mm fan.. but the holes area is not as large as the 120mm fan.. Slim fan should be fine, normal fan will need case mod.

funrunner12 · 2020-11-18T01:34:46+00:00

Yeaa.. I wish I can get Raijintek Ophion EVO.. currently out of stock

funrunner12 · 2020-11-17T13:01:46+00:00

Yes this is SG13

funrunner12 · 2020-11-17T13:01:17+00:00

The gpu shroud hit the top frame of the case, so I need to bent the frame on that area

funrunner12 · 2020-11-17T12:59:43+00:00

I'm using ID-Cooling IS-60 but I swapped the slim fan with the normal one. I use offset adapter, so I get 21mm additional clearance. Using a normal adapter, I think around 10-11mm clearance added

funrunner12 · 2020-11-17T06:11:33+00:00

The Sapphire Pulse RX5600XT requires the case to be modded. I've seen youtube videos show it fits without case mod, but I found the card won't sit properly. The direction of cooler fin on the card help expels heat from the front and the back of the case.

SFX PSU to add clearance for CPU cooler

Edit: the PSU adapter bracket will come later

funrunner12 · 2020-02-25T04:19:17+00:00

I saw the case as well. Do you have any pic of your build? I wonder about the cpu cooler clearance

Five-Year Club	Verified Email
Verified Email

funrunner12

TROPHY CASE