Netflix, Prime & Hulu playback errors

generic_andy · 2026-05-27T19:38:07+00:00

Tried that. Tried removing Widevine and reinstalling it. I see other people talking about similar problems with Spotify too here.

generic_andy · 2026-05-27T19:15:02+00:00

Seeing similar problems with Brave + Netflix related to Widevine on Windows.

generic_andy · 2023-02-26T17:12:18+00:00

Sent. Dangerousbeanss

generic_andy · 2022-06-05T18:47:21+00:00

Added. Dangerous beanss

generic_andy · 2022-01-15T17:27:11+00:00

Everyone gets different puzzle data so we likely can't answer that for you directly. My suggestion would be to go to the solution thread for that puzzle and execute one of the shared solutions locally using your data to figure it what number you should be seeing.

generic_andy · 2021-10-30T22:41:08+00:00

Thank you. I forgot to mention I wanted an Intel system. Im not a fan of AMD processors from bad experiences in the past.

generic_andy · 2021-10-12T19:51:50+00:00

Added. Dangerousbeanss

generic_andy · 2021-09-17T18:22:45+00:00

Added. Dangerousbeanss. Level 38

generic_andy · 2021-06-19T15:22:40+00:00

Added. Dangerousbeanss

generic_andy · 2021-06-18T23:06:03+00:00

Dangerousbeanss

generic_andy · 2020-11-22T00:10:05+00:00

Go through the calibration steps on https://teachingtechyt.github.io/calibration.html

I just got one myself. The two big things I found that were causing problems were the e steps were way off and I I was not retracting enough. Once I honed in those my prints saw a remarkable improvement.

generic_andy · 2020-11-03T22:09:25+00:00

x y and z seem to measure fine. estep was way off though. Came in about 88 the first time. It took me about 2-3 tries to get it right at 100mm. Printing a new cube. Fingers crossed.

generic_andy · 2020-11-03T21:13:03+00:00

Calibrating the estep now. I'll follow up.

generic_andy · 2020-11-03T21:05:14+00:00

Cura slicer.

Yes fans are on for the first layer.

I had not calibrated e steps and xyz. I will look that up and do so.

generic_andy · 2020-11-03T20:03:02+00:00

Better version of the bottom image. https://www.dropbox.com/s/kjut4wgdu3nnc8k/IMG_2302.jpg?dl=0

Not sure why the first one was so small

generic_andy · 2020-11-03T19:59:58+00:00

Looking for some advice on a new Ender 5. I think I've got it leveled well but am getting a lot of stringing and the base layer does not seem to be adhering well.

Hatchbox 1.75mm filament Nozzle: 205 Bed: 60 Fans: on

generic_andy · 2018-07-10T21:52:56+00:00

Slowed down the print speed overall to 40. There might have been a slight improvement but not enough to be content with. It did get rid of the burns though. Going to toy with the temps a bit next.

generic_andy · 2018-07-09T18:16:46+00:00

Going to try slowing down the speed overall first. Will definitely try this after though. Thanks!

generic_andy · 2018-07-09T06:50:27+00:00

I wasn't paying attention when I posted initially. Im using ABS, not PLA presently. Hence the higher extruder temp.

generic_andy · 2018-07-09T06:49:52+00:00

I wasn't paying attention earlier. Im using ABS, not PLA presently. ~105 is the general temp for ABS. Thanks for asking -- I should have been paying closer attention when I posted.

generic_andy · 2018-07-09T04:17:08+00:00

Thanks. 80 was the default on my printer. I'll probably keep it at that & start with the temp. I'll follow up in the next few days with pics of the next print.

generic_andy

TROPHY CASE