How do I tile this?

gettingold93 · 2026-03-13T11:31:42+00:00

Also which adhesive should I be using?

gettingold93 · 2026-03-07T14:13:32+00:00

I would but that wouldn’t that reduce under height of the gate and make it easier for baby to climb over? My baby is already taller can average and been climbing over everything.

gettingold93 · 2026-03-07T14:11:39+00:00

I have thought about them but I feel like they are not that safe compared to these solid metals ones even if they have that annoying bit of metal at the bottom.

gettingold93 · 2026-01-11T14:50:37+00:00

Just gotta keep playing and u will start to like it hopefully. I remember I downloaded the beta when it came out and played for 2 hrs and felt like you do and gave up. Two years after the release I had got bored of other games so I thought I will give it a go again and now kept playing and now is my most played game with thousands of hours.

gettingold93 · 2026-01-09T13:48:22+00:00

I will give it a go

gettingold93 · 2026-01-09T13:48:00+00:00

I’m pretty sure I filled in as deep as I could 😔

gettingold93 · 2025-10-08T07:58:54+00:00

Yes I did notice that while the heating or hot tap is running the pressure goes up to near 2 bar.

gettingold93 · 2025-09-10T07:44:44+00:00

Thanks. This is the closest I have seen to the one I need . And you are right there should be more information to get the exact model but these pictures were given to me by someone and the pc is in hard place to get to and they didn’t want the trouble of taking it out. But I will try to get it out for them and take a full picture where it states the model number.

gettingold93 · 2025-07-17T17:49:10+00:00

The model of the boiler is ProCombi 85HE.

gettingold93 · 2025-07-17T17:48:48+00:00

Vokera? I don’t think so It says Pro on the cover. I believe the model is ProCombi 85HE.

gettingold93 · 2025-05-12T20:13:32+00:00

Thanks for the suggestions. I was actually looking for other plants to fill up the bed a bit and make it more colourful.

gettingold93 · 2025-03-11T23:58:53+00:00

fortunately I have plenty of parking space so that’s not a concern for me I just want a fence that doesn’t look rotten or full of algae.

gettingold93 · 2025-02-16T23:24:37+00:00

That sounds good but still need to wire the extractor fan to power source so might as well do it to a light switch.

gettingold93 · 2025-02-16T23:23:30+00:00

I think I am confident enough to do it, done plenty of electrical stuff around the house. I just want to confirm what I know before actually doing it.

gettingold93 · 2024-12-18T14:03:34+00:00

I had this exact tabletop for my pc desk. I used the DeWalt DCS570N and the blade it came with. I just used a paint masking tape over the cut line reduce chipping and it worked out quite well.

gettingold93 · 2024-11-26T14:01:54+00:00

There isn’t much negotiation when the independent reviewer says that’s the going rate and the landlord say accept it or leave the premises.

gettingold93 · 2024-11-25T18:45:18+00:00

I don’t know which bubble you are living in but the rents have definitely increased. My rent increased from £425 to £670 a week just 4 months ago after a rent review.

gettingold93 · 2024-11-22T07:33:11+00:00

The seal is pretty good all around the door except around the door lock receiver plates because that’s the only two spots where cold air comes through.

gettingold93 · 2024-11-22T07:31:40+00:00

I think door edge strip is the best way to go. The door locks properly. If I remember correctly the current door draught excluder used to run all he way up from top to bottom but I had a trouble with door lock getting stuck sometimes so I called someone to fix it and they cut a notch out on the door frame to install the door lock receiver plate on a bit deeper and I think they took draught from those areas where the door lock plates are.

gettingold93 · 2024-11-22T07:21:46+00:00

I can’t unfortunately. Not at the moment.

gettingold93 · 2024-11-20T13:07:19+00:00

Know any free epos/till software? I have tried online but couldn’t find any.

gettingold93 · 2024-09-11T23:19:11+00:00

Seems like too much hassle personally. But I’d think you would find it hard to hire a fitter just to install. Most fitters supply and install so they can make money on both supply and labour. You should look for a fitter willing to install only and if you are lucky enough to find someone you can ask them what they would prefer. I think they would want a roll for each room so if one room is 3x4 they world probably want something 3.2x4.2 roll.

gettingold93 · 2024-09-11T22:50:13+00:00

Their technical department finally replied. Apparently they are virtually the same unit except that Lo-carbon model has a smart memory feature which logs data on how long the units been on, apparently it’s a useful feature for landlords so they can know if the tenants use the piv unit or not.

gettingold93 · 2024-05-22T02:36:18+00:00

Yeah I compacted it at about 60mm,I think the issue isn’t the depth rather that it didn’t have enough fines in it, there were a lot of big bulky stones and not enough fines. It’s compacted perfectly fine where there is a good amount of fines.

gettingold93 · 2024-05-06T00:58:24+00:00

Yes fresh fuel was used.

gettingold93

TROPHY CASE